manualshive.com logo in svg

Toro 68021HD, Руководство оператора

Поделиться
Скачать
Toro 68021HD Скачать руководство пользователя страница 13

OFF

ON

1

OFF

ON

G021 103

2

Figure 11

1.

Off position

2.

On position

Recoil-start Handle

To start the engine, pull the recoil-start handle (

Figure 9

)

quickly to turn the engine over. The engine controls described
above must all be set correctly for the engine to start.

Oil-level Switch

The oil-level switch is located inside the engine, and it does
not allow the engine to run in the event the oil level is below
the safe operating limit.

Specifications

Note:

Specifications and design are subject to change

without notice.

Machine Specifications

Batch Capacity

0.23 m

3

(8.0 ft

3

)

Total Volume

0.25 m

3

(9.0 ft

3

)

Drum Material

Polyethylene

Length

(without tow pole)

193 cm
(86 inches)

Width

86 cm
(34 inches)

Height

137 cm
(54 inches)

Weight

266 kg
(585 lb)

Axle

86 to 117 cm (34 to 46 inches)
extendable

Engine

Honda

®

GX240

Drive

Belt

Operation

Preparing to Tow the Machine

Important:

Ensure that your tow vehicle has towing

capacity for the weight of the machine.

Important:

Use a Class 2 or larger receiver.

Note:

Ensure that your tow vehicle has the appropriate hitch

to tow the machine; options include a 50 mm (2 inch) ball
hitch or a pintle hitch.

Note:

If the machine is equipped with a trailer-light kit,

ensure that the electrical connector of the tow vehicle is
compatible with the electrical connector of the machine. The
machine uses a standard 4-flat plug. If your tow vehicle has a
different type of plug, obtain an adapter from an automotive
parts store.

1.

Ensure that the engine is shut off, the fuel valve is in
the O

FF

position, and the drum is empty.

2.

If the drum has accumulated any water, dump the
drum; refer to

Dumping the Drum (page 24)

, steps

1

,

3

,

4

, and

5

.

3.

Using the dump lever, position the drum so that it is in
the mix position (upright) and locked.

4.

Close the engine cowl and secure the cowl latches
(

Figure 12

).

G019741

Figure 12

5.

Extend the axle; refer to

Extending the Axle (page 17)

.

13

 

Содержание 68021HD













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды