manualshive.com logo in svg

Toro 68021HD, Руководство оператора

Поделиться
Скачать
Toro 68021HD Скачать руководство пользователя страница 12

Drum Latch

The drum latch secures the drum to the mix position (upright)
for mixing operations and when transporting the machine.

1

G019877

Figure 8

1.

Drum latch

Dump Handle

Use the dump handle to rotate the drum to the dump position
and to rotate the drum to the mix position (upright).

Engine Controls

1

2

3

4

5

6

7

8

G019744

Figure 9

1.

Recoil-start handle

5.

Fuel cap

2.

Fuel valve

6.

Dipstick

3.

Choke lever

7.

Oil-drain plug

4.

Throttle lever

8.

On/Off switch

Fuel Valve

The fuel valve (

Figure 10

) is located underneath the choke

lever. Move the lever for the fuel valve to the O

N

position

before attempting to start the engine. When you have finished
mixing, shut off the engine and move the fuel valve lever to
the O

FF

position.

1

2

3

G018792

Figure 10

1.

Fuel valve

3.

Throttle lever

2.

Choke lever

Choke Lever

Use the choke lever (

Figure 10

) to start a cold engine. Before

pulling the recoil-start handle, move the choke lever to the
C

LOSED

position. Once the engine is running, move the

choke lever to the O

PEN

position. Do not use the choke if the

engine is already warmed up or if the air temperature is high.

Throttle Lever

The throttle lever (

Figure 10

) controls the speed (rpm) of the

engine. It is located next to the choke lever. It sets the engine
speed and therefore can increase and decrease the rotation
speed of the mixing paddles. For best performance, set this
control to the F

AST

position when mixing material.

Engine On/Off Switch

Use the On/Off switch (

Figure 11

) to start and shut off the

engine. This switch is located on the front of the engine.
Rotate the On/Off switch to the O

N

position to start and run

the engine. Rotate the On/Off switch to the O

FF

position

to shut off the engine.

12

 

Содержание 68021HD













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды