manualshive.com logo in svg

Toro 68021HD, Руководство оператора

Поделиться
Скачать
Toro 68021HD Скачать руководство пользователя страница 40

Storage

Storing the Machine

For storage over 30 days, prepare the machine as follows:

1.

Remove dirt and grime from the external parts of the
entire machine, especially the engine. Clean dirt and
debris from the outside of the engine cylinder-head
fins and blower housing.

Important:

You can wash the machine with mild

detergent and water.

2.

Condition the fuel system as follows:

A.

Add a petroleum-based stabilizer/conditioner to
fuel in the tank. Follow the mixing instructions
from the stabilizer manufacturer.

Do not

use an

alcohol-based stabilizer (ethanol or methanol).

Important:

Do not store

stabilizer/conditioned fuel over 90 days.

Note:

Fuel stabilizer/conditioner is most

effective when mixed with fresh fuel and used at
all times.

B.

Run the engine for 5 minutes to distribute the
conditioned fuel through the fuel system.

C.

Shut off the engine, allow it to cool, and drain the
fuel tank using a pump-type siphon. Dispose of
fuel properly; recycle it according to local codes.

D.

Start the engine and run it until it stops.

E.

Choke the engine.

F.

Start and run the engine until it does not start
again.

3.

Clean the sediment cup; refer to

Cleaning the

Fuel-Sediment Cup (page 35)

.

4.

Service the air cleaner; refer to

Servicing the Air

Cleaner (page 29)

.

5.

Change the engine crankcase oil; refer to

Changing the

Engine Oil (page 31)

.

6.

Remove the spark plug and check the condition; refer
to

Removing the Spark Plug (page 31)

.

7.

Condition the engine as follows:

A.

Remove the spark plug and pour 2 tablespoons
of engine oil into the spark-plug hole; refer to

Removing the Spark Plug (page 31)

.

B.

Pull the recoil-start handle slowly to crank the
engine and distribute the oil inside the cylinder.

C.

Install the spark plug; refer to

Installing the Spark

Plug (page 32)

.

Note:

Do not install the wire on the spark plug.

8.

Grease the machine; refer to

Lubricating the Bearings

and Seals (page 28)

.

9.

Check and tighten all bolts, nuts, and screws. Repair or
replace any part that is damaged.

10.

Paint all scratched or bare metal surfaces with paint
available from your Authorized Toro Dealer.

11.

Store the machine in a clean, dry garage or storage area.

12.

Cover the machine to protect it and keep it clean.

40

 

Содержание 68021HD













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды