Toro 41179 Скачать руководство пользователя

Страница: 37 / 68

Important:

Refer to your engine

Operator’s Manual

for additional maintenance procedures.

Daily Maintenance Checklist

Duplicate this page for routine use.

For the week of:

Maintenance Check Item

Mon.

Tues.

Wed.

Thurs.

Fri.

Sat.

Sun.

Check the brake and parking brake
operation.

Check the gear shift/neutral operation.

Check the fuel level.

Check the engine oil level.

Check the transaxle oil level.

Inspect the air filter.

Inspect the engine cooling fins.

Check any unusual engine noises.

Check any unusual operating noises.

Check the tire pressure.

Check for fluid leaks.

Check the instrument operation.

Check the accelerator operation.

Clean the suction strainer.

Check toe-in.

Lubricate all grease fittings.

Touch up and damaged paint.

Immediately after

every

washing, regardless of the interval listed

Notation for Areas of Concern

Inspection performed by:

Item

Date

Information

Содержание 41179





































































Результаты поиска

Содержание 41179

Отзывы:

Похожие инструкции для 41179

Бренды по названию

Популярные бренды

Toro 41179, Руководство оператора

Результаты поиска

Содержание 41179

Отзывы:

Похожие инструкции для 41179

Бренды по названию

Популярные бренды