Toro 41179 Скачать руководство пользователя

Страница: 61 / 68

Problem

Possible Cause

Corrective Action

1. The speed sensor is not calibrated

correctly.

1. Calibrate the speed sensor.

The Distance is inaccurate.

2. The speed sensor is damaged.

2. Contact your Authorized Service

Dealer.

1. The monitor cable is loose.

1. Connect the monitor cable.

2. The flow meter is dirty or clogged.

2. Clean the flow meter.

3. The flow meter is not calibrated

correctly.

3. Calibrate the flow meter.

The monitor does not display Application
Rate or Total Volume.

4. The flow meter is damaged.

4. Contact your Authorized Service

Dealer.

1. The flow meter is dirty or clogged.

1. Clean the flow meter.

2. The flow meter is not calibrated

correctly.

2. Calibrate the flow meter.

The Total Volume is inaccurate.

3. The flow meter is damaged.

3. Contact your Authorized Service

Dealer.

The monitor displays 6553.5 when in the
Application Rate setting.

1. The monitor is not receiving data from

the speed sensor.

1. Contact your Authorized Service

Dealer.

The monitor is erratic in operation.

1. A two-way radio is too close to the

monitor or its cables.

1. Keep two-way radios away from the

monitor and its cables.

The displayed measurements do not make
sense.

1. The Units of Measurement is set to a

system other than what you expect.

1. Check the Units of Measurement to

ensure that it is set correctly.

The monitor reads “OFL.”

1. The data has exceeded the maximum

allowed.

1. Press and hold the [Reset] button to

clear the monitor.

Содержание 41179





































































Результаты поиска

Содержание 41179

Отзывы:

Похожие инструкции для 41179

Бренды по названию

Популярные бренды

Toro 41179, Руководство оператора

Результаты поиска

Содержание 41179

Отзывы:

Похожие инструкции для 41179

Бренды по названию

Популярные бренды