Toro 22970 Скачать руководство пользователя страница 42

Страница: 42 / 48

Troubleshooting

Problem

Possible Cause

Corrective Action

1. The battery is discharged.

1. Charge the battery or replace it.

2. The electrical connections are corroded

or loose.

2. Check the electrical connections for

good contact.

The starter does not crank (model 22971
only).

3. The relay or switch is damaged.

3. Contact your Authorized Service

Dealer.

1. The fuel tank is empty.

1. Fill the fuel tank with gasoline.

2. The fuel shutoff valve is closed.

2. Open the fuel shutoff valve.

3. The choke is not on.

3. Move the choke lever fully forward.

4. The air cleaner is dirty.

4. Clean or replace the air cleaner

elements.

5. The spark plug wire is loose or

disconnected.

5. Install the wire on the spark plug.

6. The spark plug is pitted, fouled, or the

gap is incorrect.

6. Install a new, correctly gapped spark

plug.

The engine will not start, starts hard, or
fails to keep running.

7. Dirt, water, or stale fuel is in fuel

system.

7. Contact your Authorized Service

Dealer.

1. The engine load is excessive.

1. Reduce ground speed.

2. The air cleaner is dirty.

2. Clean or replace the air cleaner

elements.

3. The oil level in crankcase is low.

3. Check and add oil to the crankcase.

4. The cooling fins and air passages

under the engine blower housing are
plugged.

4. Remove any obstructions from the

cooling fins and air passages.

5. The spark plug is pitted, fouled, or the

gap is incorrect.

5. Install a new, correctly gapped spark

plug.

Engine loses power.

6. Dirt, water, or stale fuel is in fuel

system.

6. Contact your Authorized Service

Dealer.

1. The engine load is excessive.

1. Reduce ground speed.

2. The oil level in crankcase is low.

2. Check and add oil to the crankcase.

The engine overheats.

3. The cooling fins and air passages

under the engine blower housing are
plugged.

3. Remove any obstructions from the

cooling fins and air passages.

Abnormal vibration.

1. The engine mounting bolts are loose.

1. Tighten the engine mounting bolts.

1. The parking brake is on.

1. Release the parking brake.

2. The hydraulic fluid level is low.

2. Check and add hydraulic fluid.

3. The tow valves are open.

3. Close the tow valves.

The machine does not drive.

4. The hydraulic system is damaged.

4. Contact your Authorized Service

Dealer.

1. Sand or debris has built up in a tooth

root of the drive sprocket.

1. Run the chain backwards and then

reduce the chain tension.

2. The digging chain is too tight.

2. Adjust the digging chain tension.

3. The trencher boom end bearing has

failed.

3. Contact your Authorized Service

Dealer.

4. The trencher drive system is damaged.

4. Contact your Authorized Service

Dealer.

The chain does not turn

5. The hydraulic system is obstructed,

contaminated, or damaged.

5. Contact your Authorized Service

Dealer.

Содержание 22970

















































Результаты поиска

Содержание 22970

Отзывы:

Похожие инструкции для 22970

Бренды по названию

Популярные бренды

Toro 22970, Руководство оператора

Результаты поиска

Содержание 22970

Отзывы:

Похожие инструкции для 22970

Бренды по названию

Популярные бренды