Toro 22970 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 48

background image

5. Wait five to ten minutes after filling the battery cells.

Add distilled water, if necessary, until the electrolyte
level is up to the Upper line (Figure 42) on the
battery case.

6. Install the battery vent caps.

Charging the Battery

Charging the battery produces gasses that can
explode.

Never smoke near the battery and keep sparks
and flames away from battery.

Important:

Always keep the battery fully charged

(1.265 specific gravity). This is especially important
to prevent battery damage when the temperature is
below 32°F (0°C).

1. Remove the battery from the chassis; refer to

Removing the Battery.

2. Check the electrolyte level; refer to Checking the

Electrolyte Level.

3. Make sure the filler caps are installed in battery.

Connect a 3 to 4 amp battery charger to the battery
posts. Charge the battery at a rate of 3 to 4 amperes
for 4 to 8 hours (12 volts).

Do not overcharge the

battery.

4. When the battery is fully charged, unplug the charger

from the electrical outlet, then disconnect the
charger leads from the battery posts (Figure 43).

5. Install the battery onto the machine and connect the

battery cables, refer to Installing the Battery.

Note:

Do not run the machine with the battery

disconnected, electrical damage may occur.

Figure 43

1.

Positive Battery Post

3.

Red (+) Charger Lead

2.

Negative Battery Post

4.

Black (-) Charger Lead

Replacing the Fuses (Model
22971 Only)

There are 4 fuses in the electrical system. They are under
the control panel on the left side (Figure 44).

Start Circuit

30 amp

Charge Circuit

25 amp

Cooler fan Circuit

15 amp

Headlight (optional)

15 amp

Figure 44

1.

Fuse block

31

«
...
29
30
31
32
33
...
»

Содержание 22970

















































Отзывы:

Нет отзывов

Похожие инструкции для 22970

Бренд: Hagie Страницы: 61

Бренд: iBin Страницы: 2

Бренд: Danelec Страницы: 67

Бренд: W&H Med Страницы: 122

Бренд: Xiitech Страницы: 6

Ti-Max NLX nano

Бренд: NSK Страницы: 38

Бренд: Sensio Страницы: 3

Chandler Engineering 1910

Бренд: Ametek Страницы: 46

Бренд: ORORO Страницы: 16

Бренд: ASIA TECHNOLOGY Страницы: 38

Бренд: Testboy Страницы: 16

GR-292/M/HL/ADR

Бренд: olympia electronics Страницы: 8

Бренд: UCHIDA Страницы: 113

Бренд: Eaton Страницы: 6

Бренд: Major Страницы: 16

The Vienna Trellis

Бренд: Eden Страницы: 5

Бренд: AVE Страницы: 8

Бренд: EuroLite Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды