Toro 22045 Скачать руководство пользователя страница 4

Страница: 4 / 24

16. Do not start the engine when standing in front of the

discharge chute.

17. Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

18. Never pick up or carry a lawnmower while the engine

is running.

19. Stop the engine and disconnect the spark plug wire.

•

before clearing blockages or unclogging chute;

•

before checking, cleaning or working on the
lawnmower;

•

after striking a foreign object. Inspect the
lawnmower for damage and make repairs before
restarting and operating the lawnmower;

•

if lawnmower starts to vibrate abnormally (check
immediately).

20. Stop the engine

•

whenever you leave the lawnmower;

•

before refuelling.

21. Reduce the throttle setting during engine shut down

and, if the engine is provided with a shut-off valve,
turn the fuel off at the conclusion of mowing.

Maintenance And Storage

1. Keep all nuts, bolts and screws tight to be sure the

equipment is in safe working condition.

2. Never store the equipment with gasoline in the tank

inside a building where fumes may reach an open
flame or spark.

3. Allow the engine to cool before storing in any

enclosure.

4. To reduce the fire hazard, keep the engine, silencer,

battery compartment and gasoline storage area free of
grass, leaves, or excessive grease.

5. Check the grass catcher frequently for wear or

deterioration.

6. Replace worn or damaged parts for safety.

7. If the fuel tank has to be drained, this should be done

outdoors.

Sound Pressure Level

This unit has an equivalent continuous A-weighted sound
pressure at the operator ear of: 83.6 dB(A), based on
measurements of identical machines per ANSI
B71.5-1984 procedures.

Sound Power Level

This unit has a sound power level of: 100 dB(A)/1 pW,
based on measurements of identical machines per
Directive 84/538/EEC and amendments.

Vibration Level

This unit has a maximum hand-arm vibration level of 3.45
m/s

, based on measurement of identical machines per

ISO 5349 procedures.

Symbol Glossary

Safety alert triangle —
symbol within triangle
indicates a hazard.

Do not open or
remove safety shields
while engine is
running.

Safety alert symbol

Rotating blade can cut
off toes or fingers.
Stay clear of mower
blade as long as
engine is running.

Read operator’s
manual.

To avoid blade failure
when mulching, use
blade stiffener when
mower is equipped
with mulching plug.

Содержание 22045

























Результаты поиска

Содержание 22045

Отзывы:

Бренды по названию

Популярные бренды

Toro 22045, Руководство оператора

Результаты поиска

Содержание 22045

Отзывы:

Бренды по названию

Популярные бренды