manualshive.com logo in svg

Toro 22045, Руководство оператора

Поделиться
Скачать
Toro 22045 Скачать руководство пользователя страница 20

20

WARNING

POTENTIAL HAZARD

•

Grass clippings and other objects can be
thrown from an open discharge tunnel.

WHAT CAN HAPPEN

•

Thrown objects can cause serious injury or kill
operator or bystanders.

HOW TO AVOID THE HAZARD

•

Never start or operate the mower unless one of
the following is true:

1. The discharge tunnel plug is locked
securely in discharge tunnel.

2. The grass bag is locked in place.

3. The optional side discharge chute is locked
in place.

4. The discharge tunnel door is locked in
place.

Underside of Mower Housing

Keep underside of mower housing clean. Be especially
careful to keep kickers free of debris 
(Fig. 30).

m-796

Figure 30

1.

Kicker plates

Washing Method

1. Position mower on a flat surface near a garden hose.

2. Attach a quick disconnect coupling (sold separately) to

the end of the garden hose. Attach coupling to mower
washout fitting and turn water on high (Fig. 31).

1

2

3

m-2858

Figure 31

1.

Washout fitting

2.

Quick disconnect coupling

3.

Hose

3. Start the engine.

4. Engage the blade.

5. Let mower run for two minutes.

6. Disengage the blade.

7. Stop the engine.

8. Turn the water off and remove coupling from the

washout fitting.

9. Restart mower and let it run for one minute to dry out

moisture on the mower and its components.

10. If underside of mower deck has excessive grass

build-up or packing, reconnect the hose to the washout
fitting, turn the water on high and run the mower for
two minutes. Stop the mower and turn off the water.
Let the mower soak for 30 minutes. Then turn the
water on high again and run the mower for another two
minutes.

WARNING

POTENTIAL HAZARD

•

A broken or missing washout fitting could
expose you and others to thrown objects or
blade contact.

WHAT CAN HAPPEN

•

Contact with thrown debris or blade contact
will cause injury or death.

HOW TO AVOID THE HAZARD

•

Replace broken or missing washout fitting
immediately before using mower again.

•

Plug any hole(s) in mower with bolts and lock
nuts.

•

Never put your hands or feet under the mower
or through openings in the mower.

Содержание 22045

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды