TROJA CLASSIC
www.topro.no
8
EN
EN
Important to know about safety before use
•
Take care when folding and unfolding, do not trap your fingers.
•
Check the brakes every time before use and that the rollator locks into position when opened.
•
Not to be used by persons heavier than the maximum user weight (see table).
•
Do not use to transport heavy loads or persons.
•
The rollator is not a toy and therefore should be treated in an appropriate manner.
•
Make sure that the lock wheel for height adjustment for the handles is locked tightly.
•
Be aware that some parts of the rollator might feel hot or cold when exposed to extreme temperatures.
•
Do not alter the product as this might put your safety at risk and the guarantee will not be void.
Important to know about safety when in use
2
•
When stationary or parked, always use the parking brakes on both sides A
•
Before sitting on the seat, make sure the parking brakes on both sides are in the locked position A
•
Do not lean or bend sideways or over the back of the rollator whilst in the seated position. Do not tilt the rollator
more than max. 5° sideways, to avoid risk of falling. Due to the same reason bags etc. must never be hung on the
handlebars.
•
The driving brakes can be held in a little B to reduce speed, but must not be in locked position when the rollator
is in motion.
•
To give the right support and safety, make sure the rollator is kept as close to your body as possible C
•
Walk straight, look forward and hold your backside in D. That is the easiest way to keep your balance.
•
Do not push the rollator too far from your body as this can cause unnecessary strain and you could fall.
•
Be aware that the rollator may roll faster than you walking downhill, which may put you in risk of falling.
•
Do not use the rollator on stairs. Be careful when descending kerbs.
•
Be careful of flared skirts and trousers as they could be caught between the brake block and wheel, which could
lead to falling. We therefore recommend not wearing flared/wide clothing.
•
For safety reason it is prohibited to sit on the rollator during public transportation. Place your rollator securely and
use the parking brake.
Assembling / adjusting
TOPRO TROJA is delivered assembled. Before use, you must unfold the rollator. The height of the handlebar tubes will
then need adjusting to suit the user’s needs.
Unfolding / folding
3
Unfolding: Loosen the lock clamp that is over the seat bars A. Press the seat bars down and out B. The side frames
will slide apart. Press down the seat bars. You will hear a clicking sound. The rollator is now locked in its open position.
Folding: Pull the strap on the seat C and press the side frames together. Lock the clamp D over the seat bars.
Lowering and height adjusting of the handles
4
Lowering: Unscrew the lock wheel for the brake handles A (approx. 4–5 turns). Push the handlebar tubes down until
they stop B. Tighten the lock A again.
Height adjusting: Unscrew the lock for the brake handles A (approx. 4–5 turns). Adjust the handlebar tubes
to a suitable height then pull them slightly up and down C until you hear a clicking sound. Tighten the lock A again.
Adjust both handlebars to the same height.
It is recommended that the handlebars are set to the same height as your
wrists when your arms are hanging alongside your body.
Height adjustment using the memory function
5
You have the opportunity to set the height of the handles at a standard setting fitted to your requirements so that
you easily can find the same height again. This can be necessary when the rollator is being transported or stored as
compact as possible. Decide the height of the handlebars. Count visible holes at the back of the handlebar tubes.
Unscrew the lock wheel A. Pull the tube B out of the frame. The attached part C will now follow the handlebar tube.
Move the attached part C on the tube B so the amount of holes corresponds to the amount counted earlier. Fit the
memory chip D on the handlebar tube in the first available hole under the attached part C. Push the handlebar tube
B down and into the side frame E until the attached part is locked. Screw the lock wheel A half in. Pull the handlebars
F up until they stop and then tighten the lock wheel A properly. From now on, when the handlebars are in the lowest
position, they will stop in the preset position automatically when pulled up.
