Topdon Phoenix Pro Скачать руководство пользователя

Страница: 89 / 142

Phoenix Pro User Manual

Data sending indicator

Indicator (green) for sending data to main
unit.

3 Power

indicator

It keeps steady on (red) after the sensorbox
is powered on.

Type-B USB port

Connect to main unit with USB cable when it
is applied as separated USB device.

5 Power

connector

Connect to power supply through the power
adaptor.

COM

Common terminal of multimeter

7 V

Ω

Testing terminal of multimeter

9.2.2 Sensorbox accessories

The sensorbox accessories include sensor test cable, probe etc. See Table 9-2.

As the product configuration can be different, the accessories included with the
product may differ from the accessories listed on this manual. Please see the
packing list attached to the product for the detailed accessories.

Table 9-2 Accessory checklist

No.

Name

Picture

Sensor test cable

2 Sensor

probe

3 Multimeter

probe

Electronic control converting
cable 1

Electronic control converting
cable 2

Electronic control converting

Содержание Phoenix Pro















































































































































Результаты поиска

Содержание Phoenix Pro

Отзывы:

Похожие инструкции для Phoenix Pro

Бренды по названию

Популярные бренды

Topdon Phoenix Pro, Руководство пользователя

Результаты поиска

Содержание Phoenix Pro

Отзывы:

Похожие инструкции для Phoenix Pro

Бренды по названию

Популярные бренды