Topdon Phoenix Pro Скачать руководство пользователя страница 35

Страница: 35 / 142

Phoenix Pro User Manual

2. Connect the other end to the USB port of the PC. The power indicator of the

VCI connector lights up.

3. Enter Bluetooth setting screen by tapping “Settings” -> “Bluetooth”, slide the

Bluetooth switch to ON and the tablet will start searching for all available
Bluetooth devices.

Fig. 4-14

4. Tap the desired VCI connector to pair and match. By default, the Bluetooth

name of the connector is 98********00 (where ******** stands for 8 digits.).

5. If the Bluetooth pair request pops up on the screen, enter the request pin

code (default code: 0000 or 1234).

6. Once the VCI is paired with the tablet, “Paired” appears and the VCI will be

shown under the paired device tab.

*Note: In case no Bluetooth setting is done before diagnostic software is launched, you

can also configure it in process of vehicle diagnosis.

Содержание Phoenix Pro















































































































































Результаты поиска

Содержание Phoenix Pro

Отзывы:

Бренды по названию

Популярные бренды

Topdon Phoenix Pro, Руководство пользователя

Результаты поиска

Содержание Phoenix Pro

Отзывы:

Бренды по названию

Популярные бренды