Toparc 063754, Руководство пользователя

Страница: 9 / 30

9
MIG 15 / MIG 25 / MIG 36 / TT120 / PT120
EN
1
Sheath
MIG 15 MIG 25
MIG 36
Steel Alu Steel Alu Steel Alu
Ø 0.6/0.8 mm
3 m 041592 041578 - - - -
4 m 041837 044050 - - - -
Ø 1.0/1.2 mm
3 m - - 041608 041585 041608 041585
4 m - - 041844 044067 041844 044067
5 m - - 062276 - 062276 -
8 m - - - 038677 - 038677
2
Contact tube
support
MIG 15 MIG 25 MIG 36
150 A
A1 x 5 042902 - -
A2 x 10 042988 - -
250 A
B1 x 5 - 042995 -
B2 x 5 - 042919 -
350 A
D1 x 3 - - 043008
D2 x 5 - - 042926
3 Contact tube
MIG 15 MIG 25 MIG 36 TT120 / PT120
Ø 0.6 x 10 041905 - - 041905
Ø 0.8 x 10 041912 -- - 041912
Ø 1.0 x 10 041929 041066 419803 041929
Ø 1.2 x 10 041974 041073 419810 041974
4 Nozzle
MIG 15 MIG 25 MIG 36 TT120 / PT120
150 A 041875 - - 041875
250 A - 041882 - -
350 A - - 041783 -
TROUBLESHOOTING, CAUSES, SOLUTIONS
SYMPTOMS POSSIBLE CAUSES SOLUTIONS
Torch overheating
The contact tube and its support are not tight
enough.
Check and tighten the contact tube and its support.
Excessive welding current. Adjust the current on the machine.
Inoperative trigger
The wire control is cutted or damaged. Repair the wire
The euro connector of the torch is not connected
correctly to the machine.
Check the connection of the torch.
Wire welded in contact tube
Incorrect settings
Contact tube used.
Check or correct the setting.
Change the contact tube.
Irregular wire feed
Roller pressure is too low or too high Change roller pressure (on the feed motor)
The feed sheathing is clogged. Clean both ends
Contact tip incompatible with the wire diameter. Change the contact tip.
The wire feeder roller is worn-out or incorrectly
fitted.
Change the wire feeder roller.
Wire feed not working correctly. Check/repair the reel
Arc between the nozzle and the part to weld
Short circuit between the contact tip and the nozzle
due to spatter.
Clean the nozzle and spray anti-spatter agent inside.
Damaged isolator contact tip. Change the nozzle.
Unstable arc
Worn-out contact tip or inadequate contact tip with
the diameter of the wire.
Check and change the contact tip.
Incorrect setting of the welding machine. Correct the setting of the welding machine.
Internal sheath wire deteriorated. Change the wire liner in the torch.
WARRANTY
The warranty covers faulty workmanship for 2 years from the date of purchase (parts and labour).
The warranty does not cover:
• Transit damage.
• Normal wear of parts (eg. : cables, clamps, etc..).
• Damages due to misuse (power supply error, dropping of equipment, disassembling).
• Environment related failures (pollution, rust, dust).
In case of failure, return the unit to your distributor together with:
- The proof of purchase (receipt etc ...)
- A description of the fault reported