background image

28 

TREADMILL MAINTENANCE 

1. LUBRICATION

After running the belt for a period of time, it must be lubricated with specially

designed silicone oil. Suggestion: 
use less than 3h per week   

lubricate once per 5 months 

use 4-7h per week 

  lubricate once per 2 months 

use more than 7h per week 

lubricate once per month 

Do  not  lubricate  too  much.  Remember  that  reasonable  lubrication  is  an 

important factor of improving thr service life of treadmill. 

2. ADJUSTING THE BELT TENSION:

All  running  belts  are  properly  set  at  the  factory  and  after  installation.  It  may  stretch  of  be  off  center  after  use.

Stretching is normal during the break-in period. For example, the user has stopped and slipped while running. When this 
occurs, the running belt should be adjusted synchronously by clockwising direction in half circle. If the running belt is too 
loose, the running belt and the roller turn skidding when walk on the belt. But too tight is not good. It is easy to increase the 
load of motor and damage motor belt and rollers, etc. 

3. CENTRING THE RUNNING BELT

All  running  belts  are  properly  set  at  the  factory  and  after  installation.  It  may  stretch  of  be  off  center  after  use.

Stretching is normal during the break-in period. The causes of phenomenon are as follows:

The treadmill is not stationed well.

Feet are not on the center of the belt when the user is exercising.

The user’s two feet are inhomogeneous.

For  artificially  caused  deviation  phenomenon,  unload rotation  for a  few  minutes  can  be  restored  to  normal.  For  the

deviation  phenomenon  which  cannot  be  automatically  recovered,  the  six  angle  wrench  in  6mm  with  random  natching  is 
adjusted gradually in half circle.   

If toward the left side of the deck, using wrench, turn the left adjustment bolt clockwise 1/4 turn and the left adjustment 

bolt counter clockwise 1/4. If toward the right side of the deck, turn the right adjustment bolt clockwise 1/4 turn and the left 
adjustment bolt counter clockwise 1/4. 

The deviation of the running belt is not in the slope of warrenty, mainly maintain by the user according to the owner’s 

mannual.Deviation will seriously damage the running belt. It must be found in time and correct in time. 

loose 

loose 

tight 

tight 

Содержание TRX8500
























Отзывы: