18
19
EN
EN
SLIT LAMP TSL-7000Z by TOMEY
SLIT LAMP TSL-7000Z by TOMEY
Immunity
test
IEC 60601
Test level
Compliance
level
Electromagnetic environment
– guidance
Portable and mobile RF communications equipment
should be used no closer to any part of the Tomey
Slit Lamp, including cables, than the recommended
separation distances calculated from the equation
applicable to the frequency of the transmitter.
Recommended separation distance
Conducted
RF IEC
61000-4-6
6 Vrms 1
50kHz to
80MHz
6 V
d = 1.2 √ p
Radiated
RF IEC
61000-4-3
10 V/m 150kHz
to 280MHz
10 V/m
d = 1.2 √ p 80MHz to 800 MHz
d = 2.3 √ p 800MHz to 2.7GHz
Where p is the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer and d is the recommended separation
distance in metres (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey¹,
should be less than the compliance level in each
frequency range.²
Interference may occur in the vicinity of
equipment marked with this symbol.
Note: At 80MHz and 800MHz, the higher frequency range applies. These guide lines may not apply in all situations.
Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
1 Field strengths from fixed transmitters, such as base stations (cellular / cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with
accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey
should be considered. If the measured field strength in the location in which the Tomey Slit Lamp is used exceeds
the applicable RF compliance level above, the Tomey Slit Lamp should be observed to verify normal operation. If
abnormal performance is observed, additional measures may be necessary, such as re-orientating or relocating the
Tomey Slit Lamp.
2 Over the frequency range 150kHz to 80 MHz, field strengths should be less than 10 V/m.
9.3 RECOMMENDED SAFE DISTANCES
Recommended separation distances between portable and mobile RF
communications equipment and the Tomey Slit Lamp
The Tomey Slit Lamp is intended for the use in an electromagnetic environment in which
radiated RF disturbances are controlled. The customer or the user of the Tomey Slit Lamp can
help prevent electromagnetic interference by maintaining a minimum distance between mobile
RF communications equipment (transmitters) and the Tomey Slit Lamp as recommended below,
according to the maximum output power of the communications equipment.
Rated maximum output
power of transmitter (W)
Separation distance according to frequency of
transmitter (m)
150 kHz to 80MHz
d = 1.2√ p
80MHz to 800MHz
d = 1.2√ p
800MHz to 2.7GHz
d = 2.3√ p
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended
separation distance din metres (m) can be determined using the equation applicable to the
frequency of the transmitter, where p is the maximum output power rating of the transmitter in
watts (W) according to the transmitter manufacturer.
Note: At 80MHz and 800MHz, the separation distance for the higher frequency applies.
These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
9.4 TECHNICAL SPECIFICATIONS
Optical System
Binoculars type
Galilean 8° converging | Galilean 0° parallel
Magnification
Drum change x6, x10, x16, x25 & x40 | x10, x16 & x25
Eyepiece
x12.5
Field of view
34, 22, 14, 8.5 and 5.5 mm | 22, 14 & 8.5mm
PD range
8° converging eyepieces, 49 – 77mm
0° parallel eyepieces, 38 – 85mm
Objective lens focal distance
107mm
Objective lens convergence angle
13°
Slit Projection System & Base
Slit Width
0-14mm continuously variable
Slit Length
14mm
Aperture diameters
0.2, 1mm square, 2, 3, 5, 9, 14 and reserved
Filters
Clear; red free; neutral density; blue;
Slit rotation
360° continuous, detents at 0° and 180°
Base travel
25mm Z-axis, 107mm X-axis, 110mm Y axis
Horizontal fine adjustment
12mm
