background image

3. TROUBLE SHOOTING

3-1  Check of  ROM  &  NMOS-RAM  -  No  calls on  the  system.

1.  Put  the  4  "LINK  SELECT"  switches  of  the  HC  upward  (Link  No.  15

SELECT) and switch on the AC power of the exchange.

2.  If there is no error, the indication lamps will not light.
3.  In the event of a memory error, the lamps may light as shown  in the example

of Fig. 1.

4.  The error  indications will  remain  on  until  you  use  Link  No.  15 for com-

munications.

3-2 Confirming of the CP normal working

If the  CP, OC and HC are working normally, the HC's indication lamps of LINE
BUSY, LINE ADDRESS and SIGNAL CODE go out.

When any of the lamps lies alight, it is possible that any of the CP, OC or HC is
faulty.
Check  first  that  the  CLOCK  lamp  of  the  HC  is  lighting,  then  confirm  that  the

CP is working normally by hearing the clicking sound of the PI unit's relay which
is produced when the relay is activated through dial operation of the paging.
If the  CP is found working normally, chances are that the HC is faulty, followed

by the OC.

3-3 Check of  CMOS-RAM (Programmed data memory)

You  hear  calling tone  instead  of confirmation  tone,  if there  is  CMOS  memory

error  at  the  time  of  initial  programming  and  registration  using station No. 200,
or  at  the  time  of  registration  to  Single  Digit  Number  or  Personal  Number  or

Remote  Number.

3-4  Dial receiving test

1.  Instead  of  the  PI-62  unit,  use the PIU-52A  (a  unit  used  in the  EXES-5000

System)  to  check  the  dial  receiving  section  of  the  CP  also  to  check  if the
signal  is correctly transmitted as dialed from the station to be tested.

2.  If  you  place  all  "LINK  SELECT"  switches  (1  ~ 4) of SW-A on the  CP-63 in

"OFF"  position,  conversation  is  impossible  but  the  dial  code  from  each
station  is  indicated  on  the  LED's of the  PIU  as dialed.  Use  this to  find  the
cause of any fault of receiving dial information.

3.  With  use of the PI-62 unit fitted

with  no  LED,  you  can  also
check  that  the  CP  receives the
dial  signal  by  hearing  the  click
sound  of  the  relay  produced
when it is activated.

Fig. 2  DIP switches

(SW-A  of the  CP)

Example

No. 1  and No. 2 out of 4 pcs

ROMs  (2732)  have  "read"

error.

No.  0  and  No.  1  out  of  4  sets
of  N-MOS  RAMs  (2114)  have
"read" error.

(One set of  RAMs consist of

2  ICs)

Indicate  memory error.

LINK  SELECT  Switches set

to  select  No.  15

Error ROM • RAM Chip No.

Fig. 1

Example of
Hands-free/Handset Station

(HF-600M/S)

Example of
Handset Station
(TL-600M/S)

Fig. 3 Dial code indication

3-5 The order of link usage.

After power is on, links are used in numerical order for each communication.

Remember this to help you when problems are found with specific links.

Remarks:

1.  Be sure to avoid  mistake  at  the time of  DIP switch  installation  and  No. 200

Programming since such mistake may lead to trouble later.

2.  Be  sure  to  make  "No.  200  Programming"  after  "Programming  Data  Table"

(attached  to  this  manual)  is filled  out.  Keep the finished  "Programming  Data

Table"  (Initial  Checking  Sheet  for  the  System  133-21-085-5)  as a part of
complete drawings for each installation.

PI-62 unit

— 13 —

Содержание CP-63




























































Отзывы: