background image

                                                                           

Page 

17

 of 

17

 

 

After the Installation

 

Walk around and inspect the shelter periodically to make sure all components are still 
firmly secured and the whole shelter is well supported. Check all bolts and nuts as well as 
all connection points to make sure they are all in good position. Check the base plates, 
adjust the ropes and tie downs if required and clean the cover regularly.

 

 

Snow accumulating on the fabric cover must be removed as soon as possible. If snow 
becomes solid ice on the cover, it will increase the weight on the roof and may collapse 
the shelter or reduce the life span. 

 

 

Keep the shelter on a dry ground most of the time. Do not keep the fabric dirt skirt under 
water all the time, otherwise the fabric will deteriorate.

 

 

We strongly recommend you remove any snow from the roof immediately. Do not 
leave any snow load on the roof overnight. Keep 3 feet of clearance on all sides at all 
times. Do not allow snow to accumulate and pile up on the sides of the building. 
Otherwise the pressure from the sides will push inwards and could lead to a 
collapse.

 

Содержание TMG-184517ST



















Отзывы: