TLV PowerTrap GP5C Скачать руководство пользователя страница 29

Страница: 29 / 30

172-65637MA-05 (GP5C PowerTrap) 8 Jun 2020

Product Warranty

1. Warranty Period

One year following product delivery.

2. Warranty Coverage

TLV CO., LTD. warrants this product to the original purchaser to be free from
defective materials and workmanship. Under this warranty, the product will be
repaired or replaced at our option, without charge for parts or labor.

3. This product warranty will not apply to cosmetic defects, nor to any product

whose exterior has been damaged or defaced; nor does it apply in the
following cases:

1) Malfunctions due to improper installation, use, handling, etc., by other

than TLV CO., LTD. authorized service representatives.

2) Malfunctions due to dirt, scale, rust, etc.
3) Malfunctions due to improper disassembly and reassembly, or

inadequate inspection and maintenance by other than TLV CO., LTD.
authorized service representatives.

4) Malfunctions due to disasters or forces of nature.
5) Accidents or malfunctions due to any other cause (such as water

hammer) beyond the control of TLV CO., LTD.

4. Under no circumstances will TLV CO., LTD. be liable for consequential

economic loss damage or consequential damage to property.

Содержание PowerTrap GP5C






























Результаты поиска

Содержание PowerTrap GP5C

Отзывы:

Похожие инструкции для PowerTrap GP5C

Бренды по названию

Популярные бренды

TLV PowerTrap GP5C, Инструкция по эксплуатации

Результаты поиска

Содержание PowerTrap GP5C

Отзывы:

Похожие инструкции для PowerTrap GP5C

Бренды по названию

Популярные бренды