TLV PowerTrap GP5C Скачать руководство пользователя страница 23

Страница: 23 / 30

172-65637MA-05 (GP5C PowerTrap) 8 Jun 2020

3. Removing/Reattaching the Snap-action Unit

Part

Disassembly

Reassembly

Hex Bolts
(M8



2 pcs)/

Spring Washers
(2 pcs)

• Using a 13 mm (

) socket wrench,

slowly loosen the two bolts that are holding
the snap-action unit to the cover.

• Coat the bolt threads with anti-seize.
• Be sure to reinsert spring washers.
• Assemble the bolts and spring washers,

then finger-tighten.

• Tighten to a torque of 35 N



m (26 lbf



ft)

Snap-action
Unit

• Support the snap-action unit with one hand

while removing the loosened bolts and
spring washers from the cover with the
other.

• Remove snap-action unit from the cover

holding it down.

• Be careful not to let any parts fall, including

the coil spring or intake-exhaust valve.

• Do not tip the snap-action unit, as the

intake-exhaust valve may fall off.

• When working with the snap-action unit,

take care not to pinch fingers, etc.

• Reinsert the snap-action unit very

carefully, inserting tips of intake-exhaust
valve into the bottom of their respective
valve seats, then continuing to insert all
the way up into the valve seat as you
reattach the snap-action unit.

• Align the snap-action unit bolt holes to the

bolt holes in the cover.

Intake-Exhaust

Valve

• Remove the intake-exhaust valve by

rotating it 90



• Remove the coil spring.

• Reattach the intake-exhaust valve by

rotating it 90



• Reattach the coil spring.

Float/
Float Pin/
Washer/
R-pin

• Remove the float and the float holder by

removing the float pin and pulling out the
R-pin.

• Be careful not to let the float fall. Do not

drop the float or lose the washers.

• Replace the float if it is filled with water or

cracked.

• Reattach the float and the spring holder by

inserting the float pin and the R-pin.

The coil spring will be inserted later.

(1 N





10 kg



)

NOTE

If drawings or other special documentation were supplied for the product, any torque

given there takes precedence over values shown in this Instruction Manual.

Spring Washer

Hex Bolt (M8)

Coil Spring

Snap-action Unit

Intake-Exhaust Valve

Coil Spring

Float Pin

R-pin

Washer

Spring Holder

Snap-action Unit

Float

Содержание PowerTrap GP5C






























Результаты поиска

Содержание PowerTrap GP5C

Отзывы:

Похожие инструкции для PowerTrap GP5C

Бренды по названию

Популярные бренды

TLV PowerTrap GP5C, Инструкция по эксплуатации

Результаты поиска

Содержание PowerTrap GP5C

Отзывы:

Похожие инструкции для PowerTrap GP5C

Бренды по названию

Популярные бренды