TLV PowerTrap GP10L Скачать руководство пользователя страница 28

Страница: 28 / 36

172-65043MA-02 (GP10L/GT10L

PowerTrap

) 9 Mar 2004

5. Removing / Reattaching the Snap-action Unit

It is not necessary to remove the float before removing the snap-action unit.

Part Disassembly

Reassembly

Lever
Arm

• Pull the end of the lever arm down until the

snap-action unit snaps over and the float end of
the lever arm is at its lowest position.

• See disassembly.

Bolts

• Using a 19 mm (¾”) socket wrench, loosen the

four bolts that hold the snap-action and lever
units to the cover.

• Coat bolt threads with anti-seize.
• Be sure to reinsert spring washers.
• Assemble the bolts and spring

washers, then finger-tighten.

• Tighten to a torque of 60 N

⋅

(44 ft

⋅

lb)

Snap-
Action
Unit

• Support the snap-action and lever units with one

hand while removing the loosened bolts from the
cover with the other.

• Be careful not to let any parts fall, including

washers and baffle plate.

• Do not tip the snap-action unit, as intake (motive

medium) and exhaust valves may fall off.

• When working with the snap-action unit, take

care not to pinch fingers, etc.

• Reinsert the snap-action unit very

carefully, inserting tips of intake
and exhaust valves into the bottom
of their respective valve seats,
then continuing to insert all the way
up into the valve seats as you
reattach the snap-action unit.

• Align the snap-action unit bolt

holes to the bolt holes in the cover.

1 N

⋅

≈

10 kg

⋅

LEVER ARM

6. Removing / Reinstalling the Motive Medium Intake and Exhaust Valves

Part / Step

Disassembly

Reassembly

Motive Medium
Intake Valve /
Exhaust Valve

• Remove each valve by

sliding it sideways away
from the center until it
comes free of its pin.

• Align each valve with its pin, and slide it to the

center.

• Make sure that the pointed intake (motive

medium) valve is on the left side, and the
rounded exhaust valve is on the right.

INTAKE VALVE

SNAP-ACTION UNIT

EXHAUST VALVE

(MOTIVE MEDIUM)

MOTIVE MEDIUM INTAKE / EXHAUST VALVE

BAFFLE PLATE

INTAKE VALVE

(MOTIVE MEDIUM)

EXHAUST VALVE

SNAP-ACTION UNIT

Содержание PowerTrap GP10L





































Результаты поиска

Содержание PowerTrap GP10L

Отзывы:

Похожие инструкции для PowerTrap GP10L

Бренды по названию

Популярные бренды

TLV PowerTrap GP10L, Инструкция по эксплуатации

Результаты поиска

Содержание PowerTrap GP10L

Отзывы:

Похожие инструкции для PowerTrap GP10L

Бренды по названию

Популярные бренды