TLV PowerTrap GP10L Скачать руководство пользователя страница 25

Страница: 25 / 36

172-65043MA-02 (GP10L/GT10L

PowerTrap

) 9 Mar 2004

1. Removing / Reattaching the Body from / to the Cover

Prepare a new, replacement cover gasket before beginning this step.

Part Disassembly Reassembly

Drain Plug

• Discharging condensate is carried out with intake

(motive medium), exhaust, inlet and outlet piping still
connected to the unit.

• Using a 300 mm (12") long adjustable wrench, slowly

loosen plug to release pressure and discharge fluid; take
care to avoid being burned by fluid discharge.

• Wrap threads with

3 – 3.5 turns of
sealing tape or apply
sealing compound.

• Tighten to a torque

of 30 N

⋅

m (22 ft

⋅

lb).

Cover Bolts

• Using a 24 mm (

⁄

") socket wrench, loosen each bolt

slowly one turn in an alternating diagonal pattern.

• Once all bolts have been loosened, verify that there is no

internal pressure before completely removing the bolts.

• Reverse steps in

disassembly.

• Tighten to a torque

of 110 N

⋅

m (81 ft

⋅

lb).

Anchors

• Remove the bolts that hold the anchor brackets to the

body and rotate the anchor brackets on their base bolts
so that they will not interfere with removal of the body
from the cover.

• Reverse steps in

disassembly.

Body / Cover • Make sure to secure sufficient space around the body to

allow it to be pulled straight off.

• As the body weighs approximately 28 kg (62 lb), use a

block and tackle hoist to assist in its removal.

• When moving the body away from and clear of the

cover, lift the body only about 1 cm (

⁄

"), to avoid contact

with the float and other internal parts.

• In addition, to avoid contact with the float when removing

the body, lift the float and the float lever slightly.

• Do not tilt the body more than 15° in any plane.

• Reverse steps in

disassembly while
referring to the
figure below.

Cover Gasket • The gasket will be destroyed upon disassembly,

adhering to both body and cover; using a scratch-free
scrapper, carefully scrape the gasket from both body
and cover surfaces.

• Check that all

pieces of old gasket
have been removed,
then install a new
gasket.

1 N

⋅

≈

10 kg

⋅

Cover Gasket

Cover
Bolt

Body

Cover

Plugs for

Water Level

Gauge

Drain Plug

Motive Medium

Supply Pipe

Condensate Inlet Pipe

Condensate

Outlet Pipe

Exhaust Pipe

GP10L shown. GT10L
configuration differs slightly

Содержание PowerTrap GP10L





































Результаты поиска

Содержание PowerTrap GP10L

Отзывы:

Похожие инструкции для PowerTrap GP10L

Бренды по названию

Популярные бренды

TLV PowerTrap GP10L, Инструкция по эксплуатации

Результаты поиска

Содержание PowerTrap GP10L

Отзывы:

Похожие инструкции для PowerTrap GP10L

Бренды по названию

Популярные бренды