TLV MB12A Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 27

background image

172-65316M-08 (MB12A/MB12AF/MB12B/MB12BF) 7 Oct 2021

1

Contents

Introduction ....................................................................... 1

Safety Considerations ....................................................... 2

Specifications .................................................................... 4

Configuration ..................................................................... 6

Installation ......................................................................... 8

Manual Operation ............................................................ 15

Maintenance .................................................................... 16

Disassembly/Reassembly ............................................... 18

Troubleshooting .............................................................. 22

TLV EXPRESS LIMITED WARRANTY ........................... 24

Service ............................................................................ 26

Introduction

Thank you for purchasing the TLV motorized ball butterfly valve.
This product has been thoroughly inspected before being shipped from the
factory. When the product is delivered, before doing anything else, check the
specifications and external appearance to make sure nothing is out of the
ordinary. Also be sure to read this manual carefully before use and follow the
instructions to be sure of using the product properly.
The TLV motorized ball butterfly valve incorporates a ball butterfly valve,
which offers a combination of the superior sealing properties of the ball valve
and the smooth rotary movement of the butterfly valve, with an electric
actuator.
If detailed instructions for special order specifications or options not contained
in this manual are required, please contact TLV for full details.
This instruction manual is intended for use with the model(s) listed on the front
cover. It is necessary not only for installation, but for subsequent
maintenance, disassembly/reassembly and troubleshooting. Please keep it in
a safe place for future reference.

«
1
2
3
4
...
»

Содержание MB12A




























Отзывы:

Нет отзывов

Похожие инструкции для MB12A

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: VAT Страницы: 29

Бренд: Balboa Instruments Страницы: 19

Бренд: Warren Controls Страницы: 16

Бренд: Datavideo Страницы: 8

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 8

Бренд: IBM Страницы: 38

CEmarking RCX221

Бренд: Yamaha Страницы: 468

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Yamaha Страницы: 2

Бренд: ZPA Pecky, a.s. Страницы: 36

Бренд: Daruifuno Страницы: 24

Бренд: SOMFY Страницы: 112

Бренд: Scanreco Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды