TLV MB12A Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 27

background image

172-65316M-08 (MB12A/MB12AF/MB12B/MB12BF) 7 Oct 2021

18

Disassembly/Reassembly

When disassembling or removing the product, wait until the internal

pressure equals atmospheric pressure and the surface of the product

has cooled to room temperature. Disassembling or removing the

product when it is hot or under pressure may lead to discharge of fluids,

causing burns, other injuries or damage.

CAUTION

Be sure to use only the recommended components when repairing the

product, and NEVER attempt to modify the product in any way. Failure to

observe these precautions may result in damage to the product or burns

or other injury due to malfunction or the discharge of fluids.

CAUTION

Make sure the power supply is OFF before carrying out work on the

wiring or inspections involving disassembly. If such work is carried out

with the power on, there is a danger that equipment may malfunction or

electric shock may occur, leading to injury or other accidents.

CAUTION

Use the following procedures to remove components. Use the same procedures in
reverse to reassemble.
(Installation, inspection, maintenance, repairs, disassembly, adjustment and valve
opening/closing should be carried out only by trained maintenance personnel.)

Detaching/Reattaching the Actuator Unit and Valve Unit

Part

During Disassembly

During Reassembly

Part Inspection

Allen
Screw

Remove with an allen
wrench

Coat threads with anti-
seize and tighten to the
proper torque

—

Spring
Washer

Remove the spring
washer

Reinsert spring washer

—

Actuator
Unit

Slowly pull actuator unit
up and off

Remount the actuator
unit

—

Connector Detach the connector

Reattach the connector

Check for deformation or
wear

Part: Allen Screw

Valve Size

Torque

Distance

Across Flats

mm

N∙m

mm

15 to 25

10

5

32 to 50

12

6

(1 N∙m

≈

10 kg∙cm)

Allen Wrench

Allen Screw

Spring Washer

Connector

Valve Unit

Actuator Unit

«
...
17
18
19
20
21
...
»

Содержание MB12A




























Отзывы:

Нет отзывов

Похожие инструкции для MB12A

Бренд: jbc Страницы: 4

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: Olsberg Страницы: 68

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Vacon Страницы: 132

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA SIEMENS Страницы: 373

Бренд: Vag Страницы: 15

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды