TLV MB12A Скачать руководство пользователя страница 22

Страница: 22 / 27

172-65316M-08 (MB12A/MB12AF/MB12B/MB12BF) 7 Oct 2021

Common Items for Screwed and Flanged Connection Models:

Part

During Disassembly

During Reassembly

Part Inspection

Body Gasket Remove the gasket

and clean sealing
surfaces

Replace with a new gasket if
damaged

—

Valve Seat
(Union/Flang
e Side)

Remove the valve
seat

Replace with a new valve seat

—

Valve Seat
O-ring

Remove the O-ring

Replace with a new O-ring; insert
into the valve seat

—

Washer

Remove the washer

Reinsert the washer

Check for
damage,
deformation, etc.

Belleville
Washer

Remove the Belleville
washer

See the drawing below for the
proper orientation of the Belleville
washer

Check for
damage,
deformation, etc.

Ball

Remove the ball

Reinsert the ball – see the drawing
below for the proper orientation

Check the sealing
area for scratches,
wear, etc.

Valve Seat
(Body Side)

Remove the valve
seat

Replace with a new valve seat

—

Valve Seat
O-ring

Remove the O-ring

Replace with a new O-ring; insert
into the inlet valve seat

—

Washer

Remove the washer

Reinsert the washer

Check for
damage,
deformation, etc.

Belleville
Washer

Remove the Belleville
washer

See the drawing below for the
proper orientation of the Belleville
washer

Check for
damage,
deformation, etc.

Bushing

Remove the bushing Replace with a new bushing

—

NOTE: Clean, then check the inside of the body for scratches, erosion, etc.

Bushing

Body

Belleville Washer

Washer

Valve Seat

O-ring

Ball

Valve Seat

Washer

Belleville Washer

Body Gasket

Union

Содержание MB12A



























Результаты поиска

Содержание MB12A

Отзывы:

Бренды по названию

Популярные бренды

TLV MB12A, Инструкция по эксплуатации

Результаты поиска

Содержание MB12A

Отзывы:

Бренды по названию

Популярные бренды