TLV COSPECT Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 22

background image

172-65254M-03 (A-COS-10) 27 Oct 2008

11

Adjustment

The

COSPECT

reducing valve should be properly adjusted for protection of the air

equipment.

1. It is necessary to blow down all pipe lines thoroughly. The blowdown is especially

important if the line is new or has been shut down for a long period of time.
Take particular care to ensure that matter such as condensate and dirt does not
remain inside the air equipment.
(Stay clear of any pressurized blow-out from the safety valve.)

2. Make sure that the shut-off valve and the bypass valve located upstream and

downstream of the

COSPECT

are completely closed.

3. Remove the spanner cap, loosen the locknut and turn the adjustment screw

counterclockwise to reduce tension on the coil spring.

4. Slowly, fully open the shut-off valve at the inlet of the

COSPECT

. Allow sufficient

time for condensate remaining at the inlet of the

COSPECT

to be discharged.

5. Slightly open the shut-off valve at the outlet of the

COSPECT

.

6. Turn the adjustment screw until the desired outlet pressure is obtained. Wait

several minutes.

7. Slowly, fully open the shut-off valve at the outlet of the

COSPECT

.

8. After setup, retighten the locknut and replace the cap.

9. When shutting down the system, always close the outlet shut-off valve first and

then the inlet valve.

Loosen the locknut

Loosen the adjustment screw

Loosen the Adjustment Screw

Decrease Pressure

Counterclockwise

Clockwise

Counterclockwise

Tighten the Adjustment Screw

Increase Pressure

«
...
10
11
12
13
14
...
»

Содержание COSPECT























Отзывы:

Нет отзывов

Похожие инструкции для COSPECT

Бренд: GE Страницы: 8

Бренд: NEC Страницы: 146

Бренд: Vasco Страницы: 32

Бренд: Abra Страницы: 16

Бренд: SAI Страницы: 16

Бренд: Hable Страницы: 3

Бренд: RKC INSTRUMENT Страницы: 10

Бренд: XtendLan Страницы: 12

Бренд: ZBA Страницы: 27

Бренд: M-system Страницы: 10

Бренд: Tenpilot Страницы: 2

Бренд: Aqua Lung Страницы: 24

Бренд: SAGEMCOM Страницы: 2

Бренд: Instant Care Страницы: 2

Soluna Remote Control

Бренд: Rollei Страницы: 8

Бренд: TSM Страницы: 2

Бренд: Daikin Страницы: 40

Бренд: Carel Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды