manualshive.com logo in svg

TLV COSPECT, Инструкция по эксплуатации

Поделиться
Скачать
TLV COSPECT Скачать руководство пользователя страница 14

 

172-65254M-03 (A-COS-10)  27 Oct 2008

 

13

Disassembly 

 

 

NEVER apply direct heat to the float. The float may explode due to 

increased internal pressure, causing accidents leading to serious injury 

or damage to property and equipment.

 

WARNING 

 

 

Use hoisting equipment for heavy objects (weighing approximately 

20 kg or more). Failure to do so may result in back strain or other injury if 

the object should fall.

 

CAUTION 

 

 

When disassembling or removing the product, wait until the internal 

pressure equals atmospheric pressure and the surface of the product 

has cooled to room temperature. Disassembling or removing the 

product when it is hot or under pressure may lead to discharge of fluids, 

causing burns, other injuries or damage.

 

CAUTION 

 

It is a recommended practice to dismantle and inspect the 

COSPECT

 once a year for 

preventive maintenance purposes. It is especially important to perform an inspection 
immediately after the initial run of a new line or before or after equipment that is out 
of service for a long period of time. (Installation, inspection, maintenance, repairs, 
disassembly, adjustment and valve opening/closing should be carried out only by 
trained maintenance personnel.) 

Remove all pressure from the piping (both upstream and downstream). Then remove 
inlet and outlet flange retaining bolts and nuts to permit removal of the 

COSPECT

. 

Secure the 

COSPECT

 in a vise to perform the inspection.

 

 

Disassembling the Adjustment Section 

Loosen the adjustment screw completely and remove the hex bolts. Having removed 
the spring housing, you will see the diaphragm retainer, coil spring and spring 
retainer. Check for seizure or any damaged screw threads. 

 
 
 
 

 

 

Nameplate 

Adjustment

Screw

Locknut

Spring

Housing

Hex

Bolt

Coil Spring

Diaphragm 

Support

Ball

Spring Retainer

Spanner Cap 

Содержание COSPECT























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды