TLV COSPECT PN-COS-16 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 27

background image

8

Installation

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

Use hoisting equipment for heavy objects (weighing approximately

20 kg (44 lb) or more). Failure to do so may result in back strain or other

injury if the object should fall.

CAUTION

Take measures to prevent people from coming into direct contact with

product outlets. Failure to do so may result in burns or other injury from

the discharge of fluids.

CAUTION

Installation, inspection, maintenance, repairs, disassembly, adjustment and valve
opening/closing should be carried out only by trained maintenance personnel.

Installation Environment

Avoid installation in the following types of environments:



Locations with ambient temperatures above 50 °C (122 °F) or below 0 °C (32 °F)*



Locations with ambient humidity above 90% RH and below 10% RH



Locations where corrosive gas is generated



Locations with heavy vibration or shock



Locations with high inductive interference or other factors that would have a

harmful effect on electrical circuitry*

*When the

PN-COS-16

is used with electrical equipment such as an electro-pneumatic

transducer, controller, etc.

1. Blowdown

Before installing the

PN-COS-16

unit, be

sure to blow down all piping thoroughly. If
this is not possible, perform a blowdown
using the bypass valve.
Blowdown is especially important for newly
installed piping or after the system has
been shut down for a long period of time.

PN-COS

Open

Closed

Closed

Blowdown with the Bypass Valve

2. Removing Seal and Cap

Before installation, be sure to remove all protective seals and caps.
(Found in 3 locations, on the product inlet and outlets.)

①

②

③

3. Installation Angle

Install the

PN-COS-16

vertically, so that the arrow

mark on the body points horizontally in the direction
of steam flow.

Allowable inclination is 10 degrees in the fore-aft
direction and 15 degrees in the plane perpendicular
to the steam flow line.

15



15



15



15



10



10



10



10



172-65588MA-02 (

PN-COS

Pneumatic Control Valve) 5 Sep 2014

«
...
7
8
9
10
11
...
»

Содержание COSPECT PN-COS-16




























Отзывы:

Нет отзывов

Похожие инструкции для COSPECT PN-COS-16

Бренд: YASKAWA Страницы: 256

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Datalogic Страницы: 15

Бренд: Jands Страницы: 7

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: Jäger Страницы: 18

Бренд: Savant Страницы: 2

Бренд: Frico Страницы: 12

Бренд: Forcepoint Страницы: 15

VPPM-...-LK Series

Бренд: Festo Страницы: 4

Бренд: SMC Networks Страницы: 12

Бренд: Therma-Stor Страницы: 20

Бренд: Daikin Страницы: 40

Бренд: Carel Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды