TLV COSPECT PN-COS-16 Скачать руководство пользователя страница 26

Страница: 26 / 27

172-65588MA-02 (

PN-COS

Pneumatic Control Valve) 5 Sep 2014

Problem Symptom

Cause

Remedy

Abnormal noises Makes a high-

pitched noise

There is too high a
reduction ratio, the flow is
too great, or there is a
high-speed open/close
valve nearby

Use two-stage reduction
Check the flow rate, use
a larger size
Install the valve as far
away as possible

There is a build-up of dirt
on the trap valve seat or
at the float base

Clean

The body is installed tilted Check the piping
The float is deformed

Check for water hammer
Replace with a new float

Steam is blowing

There is vibration in the
piping

Secure the piping

The primary pressure
exceeds the trap valve
seat maximum operating
pressure

Adjust the primary
pressure

Water is inside the float

Replace with a new float

The secondary piping is
clogged

Check the piping
Clean

Faulty steam
trap

No condensate is
discharged

The trap valve seat is
clogged

Clean
Replace with a new trap
valve seat

Содержание COSPECT PN-COS-16




























Результаты поиска

Содержание COSPECT PN-COS-16

Отзывы:

Похожие инструкции для COSPECT PN-COS-16

Бренды по названию

Популярные бренды

TLV COSPECT PN-COS-16, Инструкция по эксплуатации

Результаты поиска

Содержание COSPECT PN-COS-16

Отзывы:

Похожие инструкции для COSPECT PN-COS-16

Бренды по названию

Популярные бренды