manualshive.com logo in svg

TLV COSPECT PN-COS-16, Инструкция по эксплуатации

Поделиться
Скачать
TLV COSPECT PN-COS-16 Скачать руководство пользователя страница 2

 

1

Contents 

Introduction ........................................................................ 1

 

Safety Considerations ........................................................ 2

 

Specifications ..................................................................... 4

 

Acceptable Operating Range ............................................. 4

 

Correct Usage of the 

PN-COS-16

...................................... 5

 

Configuration...................................................................... 7

 

Installation .......................................................................... 8

 

Operation ......................................................................... 14

 

Maintenance..................................................................... 17

 

Disassembly..................................................................... 18

 

Reassembly ..................................................................... 22

 

Troubleshooting ............................................................... 23

 

Product Warranty ............................................................. 26

 

Introduction 

Thank you for purchasing the

  pneumatic control valve for steam, model 

PN-

COS-16

. 

This product has been thoroughly inspected before being shipped from the factory. 
When the product is delivered, before doing anything else, check the specifications 
and external appearance to make sure nothing is out of the ordinary. Also be sure to 
read this manual carefully before use and follow the instructions to be sure of using 
the product properly. 
The

  pneumatic control valve for steam, model 

PN-COS-16

 is a new type of 

pneumatic control valve for steam that utilizes the structure of the 

COSPECT

 series 

pilot operated pressure reducing valve, which is our unique product. Steam-using 
equipment can achieve its intended efficiency only if the steam being used is very dry. 
Using steam in which matter such as condensate, scale, types of grease or air is 
entrained can not only result in problems with the steam-using equipment and in 
lowered productivity, but can also lead to shortened service life for and malfunction of 
the control valves. 
The

  pneumatic control valve for steam, model 

PN-COS-16

, has a built-in cyclone 

separator, screen, and steam trap that eliminates these problems and makes possible 
the supply of very dry steam at a stable pressure. 
The 

PN-COS-16

 can operate automatically and provide accurate pressure control and 

temperature control when combined with the 

  SC-F70 digital indicator controller or 

a general-purpose controller. (However, for process temperature control, the desired 
process temperature must be controllable by a secondary pressure within the adjustable 
pressure range of the 

PN-COS-16

.) Additionally, manual remote setting or 2 point 

pressure switching as a pressure reducing valve is possible by combination with an air 
regulator (with relief function). 
If detailed instructions for special order specifications or options not contained in this 
manual are required, please contact

  for full details. 

This instruction manual is intended for use with the model(s) listed on the front cover. 
It is needed not only for installation, but also for subsequent maintenance, 
disassembly/reassembly and troubleshooting. Please keep it in a safe place for future 
reference. 

172-65588MA-02 (

PN-COS

 Pneumatic Control Valve)  5 Sep 2014 

 

Содержание COSPECT PN-COS-16




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды