manualshive.com logo in svg

TLV COSPECT PN-COS-16, Инструкция по эксплуатации

Поделиться
Скачать
TLV COSPECT PN-COS-16 Скачать руководство пользователя страница 19

 

18

Disassembly 

 

 

NEVER apply direct heat to the float. The float may explode due to 

increased internal pressure, causing accidents leading to serious injury 

or damage to property and equipment.

 

WARNING 

 

 

Use hoisting equipment for heavy objects (weighing approximately 

20 kg (44 lb) or more). Failure to do so may result in back strain or other 

injury if the object should fall.

 

CAUTION 

 

 

When disassembling or removing the product, wait until the internal 

pressure equals atmospheric pressure and the surface of the product 

has cooled to room temperature. Disassembling or removing the 

product when it is hot or under pressure may lead to discharge of fluids, 

causing burns, other injuries or damage.

 

CAUTION 

 

It is a recommended practice to dismantle and inspect the 

PN-COS-16

 once a year for 

preventive maintenance purposes. It is especially important to perform an inspection 
immediately after the initial run of a new line or before or after equipment such as a 
heater is out of service for a long period of time. (Installation, inspection, maintenance, 
repairs, disassembly, adjustment and valve opening/closing should be carried out only 
by trained maintenance personnel.) 

Remove all steam from the piping (both upstream and downstream). Stop supplying 
motive air to the 

PN-COS-16

. Remove the spanner cap, and then pull up the 

adjustment screw until there is no load on the coil spring. Wait for the body to cool 
before attempting to remove the 

PN-COS-16

 from the line as it may be heated with the 

residual heat of steam. Then remove the inlet and outlet flange retaining bolts and 
nuts to permit removal of the 

PN-COS-16

. Secure the 

PN-COS-16

 in a vise to perform 

the inspection. 

 

Disassembling the Adjustment Section (Drive Section) 

Make sure that the position of the adjustment screw is such that no load is applied to 
the coil spring.   
Remove the hex bolts and then take off the spring housing. Remove the C-ring with 
an appropriate tool to remove the adjustment screw. Remove the adjustment screw by 
loosening it. Then remove the packing retainer by turning it counterclockwise. 

Spanner Cap

Adjustment Screw

Spring Housing

Ball

Hex Bolt

O-ring

Packing Retainer

Gland Packing

C-ring

Spring Retainer

Coil Spring

Diaphragm Support

 

NOTE: Make sure that there are no scratches or wear on the internal parts. Do not reuse the 

O-ring and the gland packing. 

 

 

172-65588MA-02 (

PN-COS

 Pneumatic Control Valve)  5 Sep 2014 

 

Содержание COSPECT PN-COS-16




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды