manualshive.com logo in svg

TLV COSPECT PN-COS-16, Инструкция по эксплуатации

Поделиться
Скачать
TLV COSPECT PN-COS-16 Скачать руководство пользователя страница 10

 

9

  

4. Spacer Installation 

 

 

If spacing adjustment is 
necessary to accommodate 
installation, install a spacer on 
the outlet flange. 
The spacer should consist of a 
spacer, gaskets, bolts and nuts.
Fit gaskets to both sides of the 
spacer between the 

PN-COS-

16

 outlet and the pipe flange. 

Fasten with bolts and nuts. 

Correct 

spacer 

location

Incorrect 

spacer 

location

 
5. Piping Support 

 

Install the 

PN-COS-16

, paying 

attention to avoid excessive 
load, bending and vibration. 
Support the inlet and outlet 
pipes securely. 

 

6. Maintenance Space 

 

Leave sufficient space for maintenance, inspection 
and repair. 
 

(Unit:  mm (in))

200

(8)

200 (8)

150

(6)

100 (4)

150

(6)

200

(8)

 

7.  Trap Outlet Pipe 

 

For ease of maintenance, installation of 
a union connection is recommended for 
the trap outlet pipe. 
Connect the outlet pipe to a condensate 
return line, or extend it to a trench. In the 
case of the latter, make sure the end of 
the pipe is above the waterline. (Dirt and 
water may be sucked up by the vacuum 
formed during trap closure and system 
shutdown.) 

 
 

Small Hole

 

 

172-65588MA-02 (

PN-COS

 Pneumatic Control Valve)  5 Sep 2014 

 

Содержание COSPECT PN-COS-16




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды