TJERNLUND CPC-2 Скачать руководство пользователя страница 16

Страница: 16 / 16

Appendix B: CPC-3 and VFD Abridged Fault Code Guide (Continued)

Resetting the VFD and/or CPC-3

Resetting Faulted Drives from the CPC-3:

1. Press and Hold the "Save Setting" Button for 5 seconds until the display reads "Keypad Open".

2. Press the Options button. The Options Menu will appear on the display.

3. Press the "Up" arrow button until "Reset Drives" appears on the Display.

4. Press the "Save Setting" button and wait about 5 seconds for the CPC-3 to reset the drive(s). "Drives Reset" should appear

on the display.

5. To return the keypad to its normal Locked Mode state, press the "Options Button". The display should read "Key Pad Open".

6. Press the "Enter" button. The display should read "Lock Out Key Pad"

7. Press the "Save Setting" button. The display should read "Keypad Locked".

Resetting CPC-3 Faults from the CPC-3:

1. Press and Hold the "Save Setting" Button for 5 seconds until the display reads "Keypad Open".

2. Press the Options button. The Options Menu will appear on the display.

3. Press the "Up" arrow button until "Fault History" appears on the Display.

4. Press the "Enter" button. The last fault to occur within the control will appear on the display. Record the fault message.

5. Press the "Up" arrow button and record the next fault message. Continue to use the "Up" arrow button while recording all

posted faults.

6. After recording all fault messages, Press the "Up" arrow button until "Clear All Faults" appears on the display.

7. Press the "Save Setting" button.

8. To return the keypad to its normal Locked Mode state, press the "Options Button". The display should read "Key Pad Open".

9. Press the "Enter" button. The display should read "Lock Out Key Pad".

10.Press the "Save Setting" button. The display should read "Keypad Locked".

Содержание CPC-2

















Результаты поиска

Содержание CPC-2

Отзывы:

Похожие инструкции для CPC-2

Бренды по названию

Популярные бренды

TJERNLUND CPC-2, Руководство для стартапов

Результаты поиска

Содержание CPC-2

Отзывы:

Похожие инструкции для CPC-2

Бренды по названию

Популярные бренды