TJERNLUND CPC-2 Скачать руководство пользователя страница 7

Страница: 7 / 16

I-1. Testing Rotation: Single Fan

Press the increase button until the CPC-3 display shows that the fan is running at 50% speed and

verify that the

Actual Pressure

on the CPC-3 display

becomes more negative as the fan speed increases when testing Draft

applications

or more positive as the fan speed increases when testing Combustion Air

applications.

Wait up to 90 seconds for Actual Pressure to stabilize.

IMPORTANT

If the Actual Pressure DOES NOT become more negative

as the fan speed increases toward the 50% speed

when

testing Draft

applications

or more positive when testing Combustion Air

applications, continue to Section X-4 on

page 11.

If the Actual Pressure DOES become more negative for Draft

applications

or most positive for Combustion Air

applications as the fan speed increases, continue.

Record the Actual Pressure

Содержание CPC-2

















Результаты поиска

Содержание CPC-2

Отзывы:

Похожие инструкции для CPC-2

Бренды по названию

Популярные бренды

TJERNLUND CPC-2, Руководство для стартапов

Результаты поиска

Содержание CPC-2

Отзывы:

Похожие инструкции для CPC-2

Бренды по названию

Популярные бренды