TJERNLUND CPC-2 Скачать руководство пользователя страница 4

Страница: 4 / 16

E. VFD Status Verification

Determine which of the LEDs on the Status Panel, located below the red Display LED on the VFD, is lit.

FREF is lit

continue

on to record the status of Run and Alarm LEDs.

If an LED other than the FREF LED is lit,

press the DSPL button until the FREF LED becomes

lit

Indicate the status of the following LEDs located on the VFD by checking the appropriate box within the following table.

IMPORTANT
If

ANY of your indications fall within a shaded box

, continue on to Section X-3 on page 11 and locate the corre-

sponding solution.

NONE of your indications fall within a shaded box

, continue.

F. Transducer Set-Up Verification

Verify that the

sensing tube

is connected to the Transducer

Port closest to you

and furthest from the surface upon

which the transducer is mounted.

VFD

IMPORTANT CPC-3 INDICATORS

LIT

UNLIT

BLINKING

Run LED

Alarm LED

Содержание CPC-2

















Результаты поиска

Содержание CPC-2

Отзывы:

Похожие инструкции для CPC-2

Бренды по названию

Популярные бренды

TJERNLUND CPC-2, Руководство для стартапов

Результаты поиска

Содержание CPC-2

Отзывы:

Похожие инструкции для CPC-2

Бренды по названию

Популярные бренды