TITAN MODEL KITS A330-200 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 33

background image

II. ASSEMBLY

II.A. GENERAL

Vacform parts are made from high impact polystyrene (HIPS) plastic. Vacform parts
should be glued to one another using solvent based ‘glue’. 3D printed parts should be
glued to one another and to vacformed parts using cyanoacrylate (Superglue or
equivalent) or 2-part epoxy.

II.B.1. OPTION: Install wheel wells:

Wheel wells should be installed prior to assembling fuselage halves and wings.

© Titan Model Kits

18

Revision 1.4 26 Aug 2022

«
...
16
17
18
19
20
...
»

Содержание A330-200


































Отзывы:

Нет отзывов

Похожие инструкции для A330-200

Бренд: J. Perkins Страницы: 12

Бренд: Bachmann Страницы: 12

Бренд: Minicraft Models Страницы: 4

Бренд: Airflow Страницы: 4

Бренд: Lionel Страницы: 40

Sd.Kfz.7 Zugkraftivagen 8t

Бренд: Eduard Страницы: 5

Бренд: WARCRADLE SCENICS Страницы: 35

Бренд: Faller Страницы: 4

B-17F rear interior

Бренд: Eduard Страницы: 4

midnight gambler 21005

Бренд: GRAUPNER Страницы: 40

Learn Through Music

Бренд: Fisher-Price Страницы: 2

Бренд: South Coast Sailplanes Страницы: 9

Zoom P-400 Weekend

Бренд: Eduard Страницы: 2

Бренд: Z-Stuff for Trains Страницы: 4

Train Orders Building

Бренд: Lionel Страницы: 8

Бренд: ProBoat Страницы: 19

Бренд: Little Tikes Страницы: 2

Tractor Accessories Rake Twin Roto

Бренд: Jamara Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды