Time VERSALIFT VST-7500-I, Руководство оператора

Страница: 22 / 52

3-4
29084-05 03/17 VERSALIFT VST-7500-I
SPECIFICA
TIONS
The winch is hydraulically powered through a self-
locking worm gear drive, so a load-holding brake is
not required. The winch provides line speeds of 15 to
30 ft. per minute (5 to 9 m per min.). One hundred
and five feet (32 m) of 7/16-in. (11 mm) diameter
polyester rope with a clevis hook is provided.
The angle of the 3 in (75 mm) diameter jib pole is
manually adjusted; the jib-pole assembly tilts in 10°
increments from horizontal to a maximum of 50° above
horizontal. Since the pole is automatically leveled with
the platform, there is a total of 150
0
of jib pole
articulation relative to the upper boom. The jib-pole
assembly also can be rotated to any of the seven
convenient load-lifting positions to accommodate a
load. The jib pole and winch assemblies can be
easily removed when not needed.
Platform capacity is 700 lbs. (318 kg) with the jib and
winch installed. Platform capacity is 800 lbs. with
the jib and winch removed.
1000 LBS HYDRAULIC JIB AND WINCH - The
material handling jib and winch consists of a winch
and a jib pole that are automatically leveled with the
platform. This jib provides 1000 lbs. jib capacity in
any boom position.
The winch is hydraulically powered through a self-
locking worm gear drive, so a load-holding brake is
not required. The winch provides line speeds of 15 to
30 ft. per minute (5 to 9 m per min.). One hundred and
five feet (32 m) of 7/16-in. (11 mm) diameter polyester
rope with a clevis hook is provided.
The 4 in (100 mm) square jib pole hydraulically tilts
with 90
0
of travel relative to the platform, from horizontal
to vertical. Since the pole is automatically leveled
with the platform, there is a total of 190
0
of jib pole
articulation relative to the upper boom. The jib pole
also hydraulically extends and retracts, providing 16
in. (400 mm) travel, from 44 in. to 60 in. (1.1 m to 1.5
m). The jib-pole assembly also can be rotated to any
of the seven convenient load-lifting positions to
accommodate a load. The jib pole and winch
assemblies can be easily removed when not needed.
Platform capacity is 700 lbs. (318 kg) with the jib and
winch installed. Platform capacity is 800 lbs. with
the jib and winch removed.
2000 LBS HYDRAULIC JIB AND WINCH - The
material handling jib and winch consists of a winch
and a jib pole that are automatically leveled with the
platform. This jib provides from 900 to 2000 lbs. jib
capacity depending on the boom positions.
Platform capacity is 700 lbs. (318 kg) with the jib and
winch installed. Platform capacity is 800 lbs. with
the jib and winch removed.
ARTICULATED JIB – Jib and winch consisting of a
winch, two piece jib pole assembly, and articulating
arm. Up to 1000 lbs material handling can be provided
depending on boom and jib positions. The winch is
hydraulically powered by a self-locking worm gear
drive and is rated at 1000 lbs full drum. The winch
provides an average line speed of approximately 34
FPM (10 m/minute).
The 3" diameter round inner jib pole is dielectrically
tested and can be manually pinned in 5 different length
positions, for a total of 22" length adjustment. The
4" diameter round outer jib pole is manufactured from
FRP but is not dielectrically tested. The jib pole
assembly is automatically leveled with the platform
and can be hydraulically tilted from -10° to + 86° for a
total of 96°.
The jib pole assembly is mounted on an articulating
arm. The arm is compensated so the jib pole stays
at approximately the same angle relative to the ground
as the arm articulates. The arm travels 91°, providing
the equivalent to 17.5" horizontal jib pole extension
and 20" vertical jib pole extension. The jib and winch
assembly can be manually indexed about a vertical
axis in one of seven different pin positions. This
positions the jib up to 90° to either side of the boom,
for a total travel of 180°. The jib and winch assembly
can be removed without tools when not needed.
DERATED JIB CAPACITY CHARTS- Special derated
jib capacity charts are available to reduce or eliminate
the need for ballast, or to allow for the use of A-frame
outriggers. Consult the factory for details.
PLATFORM ELEVATOR (Single Platform Only) –
Hydraulically controlled platform elevator which will
raise the platform and control panel 24” at the boom
tip. Driven by a telescoping cylinder, the platform
elevator can be raised proportionally using the same
style control valve used for all boom function.
AUTOMATIC BOOM LATCH – The automatic boom
latch is designed to automatically restrain the upper
boom in the cradle when stowed and automatically
release the boom when the lift is operated. The latch
is actuated by a hydraulic cylinder and includes a
manual over-ride to open the latch without hydraulic
power.