Timberk TEC.PF3 LE 2000 IN, Инструкция по эксплуатации

Страница: 8 / 24

www.timberk.com • electric convector heater
8
2. Select the heating power mode
2.1. Press button «1» to select the low heating power, at that the indicator
light of button «1» will be illuminated.
2.2. Press button «2» to select the medium heating power, at that the
indicator light of button «2» will be illuminated.
2.3. Press button «1» and «2» to select the high heating power, at that
indicator lights of both buttons will be illuminated.
3. Set temperature
3.1. Temperature can be set within the range +5 to +30°C, in increments
of 1°C.
3.2. Factory setting of the comfort mode temperature is +24°C, factory
setting of the economy mode temperature is +17°C.
3.3. To change the comfort mode temperature, press button « » once,
at that the comfort mode indicator « » and value of the set temperature
on LED-display will be blinking, then press button « » or « » to set
the desired temperature.
3.4. To change the economy mode temperature, press button « » twice,
at that the economy mode indicator « » and value of the set temperature
on LED-display will be blinking, then press button « » or « » to set
the desired temperature.
3.5. After the desired temperature is set, the last set value will be stored
and LED-display will show the current temperature, at that if room
temperature is less than the set one, then the heating indicator « »
must be illuminated. When room temperature reaches the desired level,
the heating indicator « » will go out. The convector will maintain the set
temperature, switching on and off heating from time to time.
4. Select the operation mode
4.1. Press button « » once to select the comfort operation mode, at that
indicator « » will be illuminated on the control panel. In this mode the
convector will automatically maintain the set comfort mode temperature,
switching on and off heating from time to time.
4.2. Press button « » twice to select the economy operation mode, at
that indicator « » will be illuminated on the control panel. In this mode the
convector will automatically maintain the set economy mode temperature,
switching on and off heating from time to time.
4.3. Press button « » three times to select the antifreeze mode, at
that symbol «AF» will be shown on the LED-display. The convector will
automatically maintain temperature within the range +5°C to +7°C,
switching on and off heating from time to time.
5. Set the convector switch off timer function
5.1. When the convector is operating press button « » three times, at that
indicator « » will be blinking on the control panel, and LED-display will
show blinking value [0.0] or the last set value of the timer.
5.2. Press button « » or « »to set the convector switch off time, in
increments of 1 hour, from 0 to 24 hours. The LED-display will show the
countdown of time left until the convector is switched off.
5.3. The set time value will be stored and in 3 seconds the system will
automatically return to indicating the temperature value, at that indicator
« » will be illuminated on the control panel.
5.4. The convector will be switched off after the timer expires, indicators on
the control panel and temperature indication on the LED-display will go out,
at that red power indicator « » will be illuminated.
5.5. Switching off the unit or setting the timer value [0.] will cancel the
convector switch off timer function.
6. Set the convector switch on timer function
6.1. When the convector is switched off and only red power indicator
« » is be illuminated, press button « » and « » simultaneously,
at that a sound signal will be given, indicator « » will start blinking on the
control panel, and sense [0.] Will blink on LED display .
6.2. Press button « » or « » to set the convector switch off time, in
increments of 1 hour, from 0 to 24 hours. Setuped time value will be saved.
The LED-display will show time left until the convector is switched on will
be shown on the display and indicator « » will be illuminated on the
control panel.
6.3. The convector will be switched on to operate in the economy mode
after the timer expires, and will maintain the set temperature.
7. Audio signal
An audio signal is given when the convector is switched on and off, as well
as the buttons are pressed.
8. Lock
8.1. When the convector is operating, to lock the system simultaneously
press and hold buttons « » and « » for 3 seconds, after that symbol
«[ ]» will be shown on the LED-display. In 3 seconds temperature Value will
be shown, at that buttons on the control panel will be locked, and symbol
«[ ]» will be shown when they are pressed.
8.2. To unlock the system, press and hold buttons « » and « » for 3
seconds or switch off the convector.