Timberk TEC.PF3 LE 2000 IN, Инструкция по эксплуатации

Страница: 3 / 24

www.timberk.com • electric convector heater
3
3. PERFORMANCE PARAMETERS
12. When the unit is switched on and operating, do not touch its surface and
the surface of the control block by wet hands and any parts of the body.
13. Do not switch on the convector if its power cord or plug is damaged.
To prevent electric shock, the damaged power cord must be repaired only
in authorized service centers of the manufacturer and by skilled specialists.
14. Never try to repair it on your own. This may harm your health and affect
the unit’s guarantee maintenance.
15. Do not use the convector in open spaces outside.
16. It is forbidden to install and use the unit in bathrooms, shower rooms or
swimming pools, in the very places, where water jets or drops may contact
its surface directly when it is switched on.
17. Do not lay the convector’s power cord under carpets and do not press
it by furniture. Lay the power cord in such a manner so that it is impossible
to trip over it.
18. To switch off the unit, set the heating power mode selector into position
«OFF» and unplug the power cord. Never pull the power cord and do not
unplug it abruptly.
19. Do not thrust fingers and prevent entering of foreign objects into any
ventilation, air intakes or air outlets, since it may cause electric shock or
damage of the convector.
20. To prevent a potential fire, do not block air intakes and air outlets. Do
not hang and dry things on the convector! Use the convector only on a dry
smooth surface.
21. The convector contains internal hot and sparkling components. Do not
use the convector in places, where petroleum, paint or any other flammable
liquids are used or stored.
22. Use this convector only in the manner, set forth in this manual. Any
other use, not recommended by the manufacturer, can result in a fire,
electric shock or injuring of people.
23. By no means clean the convector when it is connected to the mains.
Do not submerge the convector into water. Never pull the power cord.
24. To prevent overheating and fire, as well as damage of internal electric
mains, do not change the length of the power cord and do not connect the
unit through electric extenders. However, if necessary, an extender may be
used if its parameters comply with the unit’s power and if it is not used by
other power energy consumers.
25. For normal operation of the unit the mains voltage must be sufficient
and its technical parameters must be in strict compliance with technical
parameters indicated on the unit. If necessary, verify characteristics of your
mains at the power energy supplier.
26. Install and operate the unit vertically only. It is forbidden to use the unit
in a horizontal or inclined position.
27. The unit must be installed in such a way so that the control panel would
be unavailable for a person, situated directly in a bathroom (in contact with
water) or a person taking a shower.
28. It is forbidden to install the unit directly under an outlet or under a laid
electric cable when outgoing heat flows come in contact with it. It may
cause their overheating and create an emergency.
29. The unit is not intended to be used by people (including children) with
limited physical, sensory or intellectual capabilities, having insufficient
experience and knowledge, unless they are supervised or received
instructions on how to use the unit from a person, responsible for their
safety. It is necessary to be careful that children do not play with the
convector.
Operation principle
Cold air in the lower part of a room at the level of feet goes through the
convector’s heating element. Expanding at the moment of heating, heat
flow runs upwards through the outlet grill louver and smoothly spreads
along the room. At that the flow’s direction, set by louver’s inclination,
creates a favorable, accelerated circulation of warm air inside a room, not
concentrating it on walls and windows.
Key features
1. Combination of a convection effect (hence the name “convector”) with
mild thermal radiation makes the heater an economical thermal energy
source, significantly increasing the number of its followers year by year.
2. Simple and efficient ways to control a temperature mode.
3. A high-precision controlled thermostat.
4. Fast self-repayment due to a high performance factor and speed of
reaching the set temperature.
5. Ease of installation, operating reliability and ease of maintenance.
6. Three-mode heating for power energy saving.
7. A built-in air ionizer (for models TEC. PF3 LE...IN).