TICA TIMS-X Series Скачать руководство пользователя

Страница: 35 / 57

Electric Control Installation

Wiring cautions

Cautions for power wiring

●

Use copper wire as power wire and do not make it too tight.

●

The IDU and ODU use different circuits: the ODU uses a three-phase power supply,

while the IDU uses a single-phase power supply

●

All the IDUs and ODUs of the same system must be supplied with power

simultaneously.

●

The distribution box shall be provided with a set of electric leakage protection device

and air switch for each module.

●

Make sure all the earth lines of the unit are connected to ground securely. Do not

connect earth lines to lightning devices, telephone line, gas pipe or tap water pipe.

Improper grounding may cause electrical shock or fire.

Cautions communication line wiring

●

TIMS independent/strong heat independent inverter VRF air conditioning unit has

both high voltage (power) line and control (communications) line. Do not connect

power line to the connecting terminal of communication cables!

●

The total length of communication line is less than 1000 m.
The shielding layer of communication line must be connected to earth lines of each

module and IDUs securely.

Sleeve

Shielding layer

Insulator

Conductor

Legends of shielded

twisted pair

●

Communication cable is well connected before being powered on. Do not remove the

power plug with power on, lest the communication chips would be damaged.

●

To prevent high voltage signal from disturbing control signal, shielded twisted pair

must be used.
Try to select shielded twisted pair with dense shielding layers and smaller lay.

●

Control signal has two polarities A and B, and different polarities cannot be

connected, otherwise communication failures may be caused;
As shown in the following figure:

Control main

board

Control main

board

Communication

interface

Communication

interface

● When power line is parallel with communication line, they shall be covered by respective

conduits and kept at some distance away.

Содержание TIMS-X Series


























































Результаты поиска

Содержание TIMS-X Series

Отзывы:

Похожие инструкции для TIMS-X Series

Бренды по названию

Популярные бренды

TICA TIMS-X Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание TIMS-X Series

Отзывы:

Похожие инструкции для TIMS-X Series

Бренды по названию

Популярные бренды