TICA TIMS-X Series Скачать руководство пользователя

Страница: 14 / 57

Installation of ODU

Handling

Notes:
●

Fragile and handle with care.

●

The degree of inclination shall not exceed 30° while handling (do not put the unit on

its side).

●

Keep heat exchange fins safe while handling and installing the unit. In case of any

damages, please use fin comb to fix it up.

●

Properly dispose of packaging bags and prevent kids from playing with them.

Hook

Hoisting rope

Protective pad

Lifting hole (two at the front

and two at the back)

Keep the ropes through the

holes to ensure stability

during hoisting.

Forklift pocket

● Use forklift to handle: be careful when inserting the fork into the pocket at the bottom,

and prevent fork from damaging the unit or the unit bottom.

●

Use crane to handle: tighten hoisting rope according to what is shown in the figure,

and keep the unit weight even during hoisting.

●

Use two hoisting ropes at least 8 m long and about 20 mm in diameter to support the

unit weight. Do not use tying band of the unit for handling.

●

After the wooden framework is removed: use paper or cloth as pad between hoisting

rope and the unit to prevent damages to the unit body.

Placement

●

Make sure the ODU is placed firmly at a level place to prevent vibration and noises.

●

Use a base larger than the width of ODU's support legs (66 mm) to support the unit.

●

The shock-absorbing pads shall cover the entire bearing surface of the base.

●

The unit base shall be at least 200 mm higher above the ground.

●

Around the base there should be drain to ensure that the condensate water

generated during operation could flow out.

Содержание TIMS-X Series


























































Результаты поиска

Содержание TIMS-X Series

Отзывы:

Похожие инструкции для TIMS-X Series

Бренды по названию

Популярные бренды

TICA TIMS-X Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание TIMS-X Series

Отзывы:

Похожие инструкции для TIMS-X Series

Бренды по названию

Популярные бренды