7
BINDING PROCESS
安全校頻配對步驟
7
A binding feature is included in the ACE RC Cougar 2.4GHz spread spectrum system to ensure the transmitter and receiver bind
properly and prevent interference from other controllers.
To manually bind Tx/Rx, please proceed as per the following steps:
a.
Press and hold the “Binding SW” button on the back side of the transmitter while turning on the transmitter.
b.
Release the “Binding SW” button after the green LED flashes indicating the transmitter is binding.
c.
Press and hold the bind button on the receiver while turning on the receiver. Binding process will then start automatically. The
LED will turn green/red flash on the receiver.
d.
Release the “Binding SW” button. Successful binding is confirmed by the binding LED changing from a quick blinking and
then remain solid on the transmitter. The LED will turn green on the receiver. Once binding is complete, the system will
automatically connect.
Note: Binding process may take 3~10 seconds to execute. If binding fails, the LED on the receiver will turn red.
Please turn off the power and repeat the steps from a) ~d).
ACE RC Cougar P3
採用最先進的專用
3
動
2.4GHz
無線展頻遙控系統。這個系統結合發射與接收可以互動溝通模式，跳動頻道搜
尋，使得整體無線遙控系統的傳輸展現精準穩定的特性同時也無須擔心頻率干擾的問題。如發現無法操控情形發生，需要重新校頻
配對，請依照下列步驟重新進行校頻配對程序：
a.
打開發射機電源時，同時持續按壓發射機背面之
"Binding SW"
按鈕。
b.
直到按鈕旁之
LED
綠燈快速閃爍，再放開
"Binding SW"
按鈕，表示發射機正在進行自動搜尋校頻，此時請不要關閉發射機電源。
c.
然後按壓接收機上之
"Binding SW"
按鈕並同時開啟接收機電源，此時接收機將自動進行校頻配對程序。接收機
LED
燈號為紅綠快
速閃爍。
d.
放開
"Binding SW"
，一旦完成配對程序，發射機
LED
燈號會從綠色快速閃爍轉換成持續綠色燈號，接收機
LED
燈號將從紅色轉換
為綠色。此時表示接收機與發射機已完成配對溝通，可以進行操控。
注意：遙控系統校頻配對可能需要
3~10
秒執行程序。如果程序執行錯誤，發射及接收模組的
LED
燈號將持續呈現紅色。請關閉
電源再依
a) ~d)
的順序重新操作配對程序。
Step
步驟
a
b
c
d
No Action
無須動作
No Action
_
_
無須動作
No Action
TX LED
：
GREEN FLASH
TX
燈號：綠燈快速閃爍
RX LED
：
GREEN/RED FLASH
RX
燈號：綠
/
紅燈快速閃爍
TX LED
：
GREEN FLASH-->GREEN SOLID
RX LED
：
RED SOLID-->GREEN SOLID
TX
燈號：
綠燈快速閃爍
-->
綠燈恆亮
RX
燈號：
紅燈恆亮
-->
綠燈恆亮
無須動作
No Action
無須動作
TX Action
動作
RX Action
動作
LED
燈號
Swithch On
開
/ Push
按
Swithch On
開
/ Push
按
Release
放開
Release
放開
