THUNDER TIGER 6724-F28 PLUS 3.5, Инструкция по эксплуатации и каталог запасных частей

Страница: 8 / 34

7
F/S-FAIL SAFE
防暴衝設定
7
How to Set the Fail Safe (F/S) Position
a. After binding the transmitter and receiver, you can continually set up the F/S position. Turn on the transmitter power and then
receiver power.
b. Press the “Binding SW” button on the receiver. 10 seconds later, the LED will turn green flash on the receiver.
(Caution! Don't release the “Binding SW” button now until STEP3 has been completed.)
c. Move and hold the throttle trigger to the F/S servo position where you want to set. Keep steering wheel at Neutral. o set up F/S with
servo position at "Brake", first push the trigger to the brake position and hold. To set up F/S with servo position at "Neutral", first pull
or push the trigger and then release to neutral.
(Caution: Always set the throttle trigger to the neutral or full brake position incase of any unexpected control error!.)
d. After the Step3, release the “Binding SW” button first and then the throttle trigger. The LED turns to solid “RED” and then back to
solid “GREEN” 2 seconds after. The F/S set up has now been activated.
e. F/S at "Neutral": To check the fail safe is working properly, by moving the throttle trigger to the full forward (full brake), hold it on this
position and then turn off the transmitter. The F/S function should move the throttle servo to "Neutral". F/S at "Brake": To check the
fail safe is working properly, by keeping the throttle trigger at neutral and then turn off the transmitter. The F/S function should move
the throttle servo to "Brake".
f. If the F/S set up fail, try the steps from a) ~f) again. After the F/S has been fully complete, you can just start your operation.
Transmitter first, receiver later.
a.
設定此功能前請先完成系統發射與接收之對頻。確定後，先打開發射機再開接收機電源。
b.
押著接收機對頻開關，約
10
秒鐘後
LED
會變為綠色快速閃爍，注意步驟
3
完成前不要放開接收機對頻開關。
c.
同時移動油門扳機至您想要設定
F/S
伺服機位置。轉向舵輪保持中立點位置。
【如想要設定
F/S
油門伺服機位置為煞車，需先移動油門扳機至煞車位置不要鬆開。】
【如想要設定
F/S
油門伺服機位置為中立，需先移動油門扳機（煞車或加速）然後再回復中立點位置。】
! 注意：防暴衝油門伺服機位置建議設定為煞車或中立點，請勿設定為油門開啟位置，以免發生危險。
d.
此時你可以放開接收機對頻開關，再放開發射機油門板機。
LED
會變為恆亮紅燈，約
2
秒後又回到恆亮綠燈，此時表示
F/S
設定成功。
e. F/S
油門伺服機位置為中立點: 將油門扳機全煞車，關掉發射機電源，檢視
F/S
伺服機位置動作是否轉回中立點位置。
F/S
油門伺服機
位置為煞車: 油門扳機保持中立點，關掉發射機電源，檢視
F/S
伺服機位置動作是否轉回煞車位置。
f.
檢查無誤後，開發射機開關，然後接收機關開始操作。
1. Steering: Neutral
2. Keep brake or trigger at neutral 1.
轉向中立
2.
保持煞車或是油門在中立點
Binding Complete
完成對頻
Release Later
後放開
OK!
a
b
c
d
e
f
完成對頻
Binding Complete
Step
步驟
TX Action
發射機動作
RX Action
接收機動作
LED
燈號
1.
1.
2.
or
No Action
無須動作
No Action
無須動作
No Action
無須動作
2.
OFF
1. Keep Brake
2. Swithch Off
1.
保持煞車
2. 關發射機
RX LED :
Red Solid-2s --> Green Solid
RX
燈號：
紅燈亮 -2 秒 --> 綠燈亮
RX LED: Green Flash
RX
燈號：綠燈快速閃爍
TX LED: Green Solid
RX LED: Green Solid
TX
燈號：綠燈亮
RX 燈號：綠燈亮
F/S Function Activates
F/S
安全回復功能啟用
Push for 10
Sceonds
持續按 10 秒
Push for 10
Sceonds
持續按 10 秒
Switch on Power
開啟電源
Switch on Power
開啟電源
Release First 先放開
Press
按
Neutral
中立
Neutral
中立
Pre-settings for F/S function:
GP Car : Steering at Neutral /
Carb. at Iddle and car
barkes
出廠預設
F/S
功能：
油車：轉向朝前，油門關閉
（怠速）