Thunder Laser NOVA-24 Скачать руководство пользователя страница 53

Страница: 53 / 77

THUNDER LASER

NOVA-35

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

4.7 How to adjust focus distance by manual or auto

1) How to adjust focus distance by manual

1. Standard laser head:

The focus distance between the standard laser head and the material is 6mm.

Find the 6mm thickness Acrylic Focus Ruler for help to adjust the focus directly like below:

①

Working Table

②

Material

③

Focus Ruler

Please note that the limit line of the head, this limit line indicates the max height of laser

head, and keep the limited line inside the laser head mount. So as to protect the laser

head from crashing into the honey comb table while z-axis does reset/auto focus

2. HR laser head

The focus distance between the HR laser head and the material is 3.5mm.

Since HR head is very sensitive for focus distance, thus we’ve tested and made a special

focus tool (with a best distance) for each HR head, like below:

①

Working Table

②

Material

③

Focus Tool

3. Four inch laser head

The focus distance between the 4” laser head and the material is 10mm.

4” laser head is not so sensitive for focus distance; you can set the distance about

10mm~12mm with the help of focus ruler, like below:

Содержание NOVA-24














































































Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды

Thunder Laser NOVA-24, Руководство пользователя

Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды