Thunder Laser NOVA-24 Скачать руководство пользователя страница 12

Страница: 12 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

2.3 Safety Precautions when Operating the Device

In your thunder laser NOVA-24, a closed safety system is integrated which immediately

stop a job when the protection cover is opened. Consequently an incomplete engraving

can occur if the cover is opened during operation. Therefore, first press the "PAUSE"

button, if you want to interrupt an engraving process.

Please remember the following safety precautions when working with this device:

1. CO2 Fire extinguishers should be placed near laser. Always keep a

properly maintained and inspected fire extinguisher on hand.

2. Do not store any flammable materials in the inside of the device.

Particularly leftovers of produced materials have to be removed to

prevent fire hazard.

3. Please maintain Free air-flow surrounding this system. At all times, do

not cover during operation.

4. Stay with the laser. Do not leave the laser unattended when it is

working, small scraps can ignite and without supervision can destroy

the machine if not checked.

5. Use Air Assist. Always use the system’s Air Assist feature when vector

cutting.

1. These lasers emit invisible radiation; safety glasses should be worn

when maintenance these machines for your protection.

2. Adjustment of the beam path must be performed only by especially

trained personnel. An improper setting can lead to uncontrolled

emission of the laser radiation.

1. Do not disable limit switches or safety features as this can invalidate

warranties and cause damage to you and the machine.

2. Before processing materials the user must verify, whether harmful

materials can be generated and whether the filter equipment of the

exhaust system is suitable for the harmful materials. We emphasize that

it is the responsibility of the user, to consider the national and regional

threshold values for dust, fogs and gases when selecting the filters and

the exhaust system. (The values for the maximum workplace

Содержание NOVA-24














































































Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды

Thunder Laser NOVA-24, Руководство пользователя

Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды