Thunder Laser NOVA-24 Скачать руководство пользователя страница 35

Страница: 35 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

4.2 ON/OFF Switch

The mains and the laser supply power ON/OFF switch

The following conditions must be fulfilled for correct start up:

Unrestricted freedom of motion of the mechanics

No materials under the engraving table

Protection covers closed

When turn on the power of machine, and note that turn on the main switch first and then

the laser supply power switch

If all covers are closed, immediately after being switched on, the device starts the

referencing process. When the referencing process is completed correctly, an acoustic

signal sounds and the device is ready for operation. The operation panel will display the

home screen when the laser is completed resets.

Before switching on the device, the user must make sure that no objects

of any kind are located inside the operating space, which could limit or

obstruct the mechanics of the device.

Содержание NOVA-24














































































Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды

Thunder Laser NOVA-24, Руководство пользователя

Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды