background image

Ø1/2" Shutters and Controller 

Chapter 11: Regulatory 

Rev F, December 9, 2018 

Page 21 

Chapter 11  Regulatory 

As required by the WEEE (Waste Electrical and Electronic Equipment Directive) 
of the European Community and the corresponding national laws, Thorlabs offers 
all end users in the EC the possibility to return “end of life” units without incurring 
disposal charges. 

 

This offer is valid for Thorlabs electrical and electronic equipment: 

 

Sold after August 13, 2005  

 

Marked  correspondingly  with  the  crossed  out 
“wheelie bin” logo (see right) 

 

Sold to a company or institute within the EC  

 

Currently  owned  by  a  company  or  institute 
within the EC  

 

Still  complete,  not  disassembled  and  not 
contaminated 

As  the  WEEE  directive  applies  to  self  contained 
operational  electrical  and  electronic  products,  this  end  of  life  take  back  service 
does not refer to other Thorlabs products, such as: 

 

Pure OEM products, that means assemblies to be built into a unit by the 
user (e.g. OEM laser driver cards)  

 

Components  

 

Mechanics and optics  

 

Left over parts of units disassembled by the user (PCB’s, housings etc.).   

If you wish to return a Thorlabs unit for waste recovery, please contact Thorlabs 
or your nearest dealer for further information. 

Waste Treatment is Your Own Responsibility 

If  you  do  not  return  an  “end  of  life”  unit  to  Thorlabs,  you  must  hand  it  to  a 
company specialized in waste recovery. Do not dispose of the unit in a litter bin 
or at a public waste disposal site. 

Ecological Background 

It is well known that WEEE pollutes the environment by releasing toxic products 
during decomposition. The aim of the European RoHS directive is to reduce the 
content of toxic substances in electronic products in the future. 

The  intent  of  the  WEEE  directive  is  to  enforce  the  recycling  of  WEEE.  A 
controlled recycling of end of life products will thereby avoid negative impacts on 
the environment. 

Содержание SHB05
























Отзывы: