THORLABS BBD102 Скачать руководство пользователя страница 68

Страница: 68 / 76

GetHWCommsOK

Gets the hardware communications OK flag.

GetJogMode

Gets the jogging button operating modes.

GetJogMode_Mode

Get the jogging button operating mode (returned by
value).

GetJogMode_StopMode

Gets the jogging button stopping mode (returned by
value).

GetJogStepSize

Gets the jogging step size.

GetJogStepSize_StepSize

Gets the jogging step size (returned by value).

GetJogVelParams

Gets the jogging velocity profile parameters.

GetJogVelParams_Accn

Gets the jogging acceleration parameter (returned
by value).

GetJogVelParams_MaxVel

Gets the jogging maximum velocity parameter
(returned by value).

GetMotorParams

Gets the motor gearing parameters.

GetParentHWInfo ;

Gets the identification information of the host
controller.

GetPosition

Gets the current motor position.

GetPosition_Position

Gets the current motor position (returned by value).

GetPositionEx

Gets the current motor position.

GetPositionEx_UncalibPosition Gets the current uncalibrated motor position

(returned by value).

GetPositionOffset Gets

the motor position offset.

GetRelMoveDist Gets

the

relative move distance.

GetRelMoveDist_RelDist

Gets the relative move distance (returned by
reference).

GetStageAxis

Gets the stage type information associated with the
motor under control.

GetStageAxisInfo

Gets the stage axis parameters.

GetStageAxisInfo_MaxPos

Gets the stage maximum position (returned by
value).

GetStageAxisInfo_MinPos

Gets the stage minimum position (returned by
value).

GetStatusBits_Bits Gets

the

controller status bits encoded in 32 bit

integer (returned by value).

GetVelParamLimits

Gets the maximum velocity profile parameter limits.

GetVelParams

Gets the velocity profile parameters.

GetVelParams_Accn

Gets the move acceleration (returned by value).

Содержание BBD102













































































Результаты поиска

Содержание BBD102

Отзывы:

Похожие инструкции для BBD102

Бренды по названию

Популярные бренды

THORLABS BBD102, Руководство пользователя

Результаты поиска

Содержание BBD102

Отзывы:

Похожие инструкции для BBD102

Бренды по названию

Популярные бренды