THOR GE559-N Скачать руководство пользователя страница 9

8

 

 

 

Installation (Continued) 
 

Wall Mounting (To Non-Combustible Wall Only)  

 
 

 
 

 
 

 
 
 

 
 

 
 
 
 
 

 
 

 
 
 

 
 

 
 

 
 
 

 
 

 
 
 

 
 

 
 
 

 

 
 
 

 
 
 

 
 

 
 
 

 
 

 
 

 
 
 

 
 

1.

 

Fix  the  wall  mounting  bracket  to  the  wall 
with  six  screws,  in  such  a  position  that  the 
top  of  the  bracket  is  level  and  at  least  945 
mm  (38”)  above  any  surface  beneath  the 
unit. This will ensure that the bottom of the 
Salamander  is  at  least  600  mm  (24”)  above 
any surface. Refer to Fig. 1 as an example. 

 
2.

 

Fit  the  two  black  plastic  spacers  to  the  top 
rear  corners  of  the  unit.  Leave  them 
unscrewed by approximately 5 mm.  Refer to 
Fig. 2 (A). 

 
3.

 

Fit the two adjusting  screws / bolts into the 
nut inserts at the bottom rear corners of the 
unit. These should protrude approximately 30 
mm from the rear of the Salamander.  Refer 
to Fig. 2 (B). 

 
4.

 

Lift  the  Salamander  onto  the  wall  bracket, 
lining  up  the  black  plastic  spacers  on  the 
salamander with the mounting notches in the 
bracket.  Refer to Fig. 3. 

 
5.

 

Lower  the  Salamander  onto  the  mounting 
bracket.   Refer to Fig. 4. 

 
6. Tighten the black spacers securely and adjust 

the leveling screws / bolts to ensure that the 
unit is level. Refer to Fig. 4. 

 

Fig. 1 

Screws 

94

5m

m

 

60

0mm

 

5mm 

Fig. 2

 

30mm 

 

 

Fig. 3

 

Fig. 4

 

Содержание GE559-N





















Отзывы: