background image

Thor Gas Salamander    

Installation and Operation Instructions      
 
 

 

Model: GE559-N GE559-P  

 

IMPORTANT FOR FUTURE REFERENCE 

Please  complete  this  information  and  retain  this  manual  for  the  life  of  the  equipment.  For  Warranty 
Service and/or parts, this information is required. 
 

 
Model Number                      

Serial Number                    

 

Date Purchased 

 
 

WARNING:

  For  your  safety,  do  not  store  or  use  gasoline  or  other  flammable  vapors  or 

liquids  in  the  vicinity  of  this  or  any  other  appliances.  Keep  the  area  free  and  clear  of 

combustible.  

 
 

WARNING

Improper  installation,  adjustment,  alteration,  service  or  maintenance  can 

cause property damage, injury, or death. Read the installation operating and maintenance 
instructions thoroughly before installing, or servicing this equipment.

 

 

WARNING

Instructions  must  be  posted  in  a  prominent  location.  All  safety  precautions 

must be taken in the event the user smells gas. Safety information can be obtained from 
your local gas   supplier. 

 

 

 
 

 
 

 
 
 

 

 

 

 

 

 

 

 

              

                                                            

15 Badgally Road, Campbelltown 

 

NSW 2560 

 

Thor after sales/service: 1300 225 960 

 

 

 

Содержание GE559-N





















Отзывы: