THOMSON Grass Valley ParkerVision Camera Man Скачать руководство пользователя страница 13

Страница: 13 / 35

Page 10

Configuring the Tracking System Keypad

Tracking System Keypad

Check the

KEYPAD ADDRESS

rotary switch (located in the battery compartment of the

keypad) and verify that the selected setting corresponds to the setting of the

BASE UNIT

ADDRESS

switch on the back of the autoTRACK camera. If the two are different, adjust them

so that they correspond.

For more information on configuring the

BASE UNIT ADDRESS

on the camera and

keypad,refer to the

CameraMan® Camera Installation and Operations Manual

that came with the camera.

If the Tracking System Keypad is being used in the wireless RF mode:

1. Install the supplied AA batteries in the Tracking System Keypad by removing the

battery door and inserting the batteries into the battery compartment.

2. After installing the batteries, replace the battery door and press one of the pan keys.

3. Look to verify that the LED on the front of the keypad illuminates. This indicates

that the batteries are installed properly.

If the LED does not illuminate, the batteries may be installed backwards. Reverse

the way the batteries are inserted, and try again.

If the batteries are inserted improperly, it will not damage the keypad, the keypad

will simply not work.

If the Tracking System Keypad is being used in the hard-wired mode, connect the CameraMan

Keypad Cable to the

RJ-11

type jack located in the battery compartment of the Tracking System

Keypad. Remove the batteries first.

You do not need batteries installed in the Tracking System Keypad when it is being

used in the hard-wired mode.

Press the

PAN

and

TILT

arrows one at a time and verify that the camera is responding to the

keypad. The

COM

LED on the front of the camera should flash with every command received

by the camera. If the

autoTRACK

LED on the front of the camera is not illuminated, press

one of the four

autoTRACK View

buttons on the keypad. This should cause the

autoTRACK

LED to begin flashing.

Refer to pages 15 through 22 for details on using the Tracking System Keypad.

Keypad Address

Tracking System Keypad

in hard-wired mode

Battery

compartment

Содержание Grass Valley ParkerVision Camera Man




































Результаты поиска

Содержание Grass Valley ParkerVision Camera Man

Отзывы:

Бренды по названию

Популярные бренды

THOMSON Grass Valley ParkerVision Camera Man, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Grass Valley ParkerVision Camera Man

Отзывы:

Бренды по названию

Популярные бренды